Changes between Version 270 and Version 271 of doc/app/parlist

Timestamp:

Mar 12, 2020 11:41:59 AM (5 years ago)

Author:

oliver.maas

Comment:

--

doc/app/parlist

@@ -42 +42 @@
 || [../salsa#aerosol_flux_sigmag aerosol_flux_sigmag] || salsa || R(7) || 1.8, 2.16, 2.21, 2.0, 2.0, 2.0, 2.0 || The standard deviation of the log-normal size distribution per aerosol emission mode. 
 || [../agtpar#agent_maximum_age agent_maximum_age] || agt || R(100) || 100 * 9999999.9 || Maximum time an agent can spend in the simulation before it is deleted. 
-|| [../wind_turbine_par#air_dens air_dens] || wtm || R ||1.225|| The air density (in kg/m^3^) is necessary to convert the aerodynamic torque of the rotor into a power (in W). 
+|| [../wind_turbine_parameters#air_density air_density] || wtm || R ||1.225|| The air density (in kg/m^3^) is necessary to convert the aerodynamic torque of the rotor into a power (in W). 
 || [../radpar#albedo albedo] || rrtmg || R || 0.2 || Surface albedo. 
 || [../radpar#albedo_lw_diff albedo_lw_diff] || rrtmg || R || depends on \\ [../radpar#albedo_type albedo_type] || Surface albedo for longwave diffuse radiation for a solar angle of 60°. 
@@ -197 +197 @@
 || [../d3par#dt_coupling dt_coupling] || run || R || 9999999.9 || Temporal interval for the data exchange in case of runs with coupled models (e.g. atmosphere - ocean) (in s). 
 || [../d3par#dt_data_output dt_data_output] || run || R || 9999999.9 || Temporal interval at which data (3d volume data, cross sections, vertical profiles, spectra) shall be output (in s). 
-|| [../d3par#dt_data_output_av dt_data_output_av] || run || R || value of \\ [../d3par#dt_data_output dt_data_output] || Temporal interval at which time averaged 3d volume data and/or 2d cross section data shall be output (in s). 
+|| [../d3par#dt_data_output_av dt_data_output_av] || run || R || value of \\ [../d3par#dt_data_output dt_data_output] || Temporal interval at which time averaged 3d volume data and/or 2d cross section data shall be output (in s).
+|| [../wind_turbine_parameters#dt_data_output_wtm] || wtm || R || 0.0 || Output interval (s) for NetCDF data. this parameter does not affect the deprecated ASCII data output that is written at each time step. With the default value 0.0 data will be output every time step.
 || [../d3par#dt_disturb dt_disturb] || run || R || 9999999.9 || Temporal interval at which random perturbations are to be imposed on the horizontal velocity field (in s). 
 || [../d3par#dt_domask dt_domask] || run || R \\ (max_masks) || max_masks * value \\ of [../d3par#dt_data_output dt_data_output] || Temporal interval at which instantaneous masked data shall be output (in s). 
@@ -222 +223 @@
 || [../agtpar#dt_write_agent_data dt_write_agent_data] || agt || R ||9999999.9|| Output interval for agent NetCDF output (in s).
 || [../parpar#dt_write_particle_data dt_write_particle] \\ [../parpar#dt_write_particle_data _data] || lpm || R || 9999999.9 || Temporal interval for output of particle data (in s). 
-|| [../wind_turbine_par#dtow dtow] || wtm || R(100) || none || Diameter of the tower of the wind turbine used below the rotor. This parameter has to be non-zero if a tower should be included. The parameter needs to be specified for every turbine separately. 
 || [../initialization_parameters#dx dx] || ini || R || 1.0 || Horizontal grid spacing along the x-direction (in m). 
 || [../initialization_parameters#dy dy] || ini || R || 1.0 || Horizontal grid spacing along the y-direction (in m). 
@@ -253 +253 @@
 || [../d3par#force_print_header force_print_header] || run || L || .F. || Steering of header output to the local file [../iofiles#RUN_CONTROL RUN_CONTROL]. 
 || [../initialization_parameters#galilei_transformation galilei_transformation] [=#g] || ini || L || .F. || Application of a Galilei-transformation to the coordinate system of the model. 
-|| [../wind_turbine_par#gear_eff gear_eff] || wtm || R || 1.0 || Efficiency of the gear: Loss between rotor and generator. 
-|| [../wind_turbine_par#gear_ratio gear_ratio] || wtm || R || 97.0 || Gear ratio from rotor to generator. 
-|| [../wind_turbine_par#gen_eff gen_eff] || wtm || R || 0.944 || Electric efficiency of the generator. 
+|| [../wind_turbine_parameters#gear_efficiency gear_efficiency] || wtm || R || 1.0 || Efficiency of the gear: Loss between rotor and generator. 
+|| [../wind_turbine_parameters#gear_ratio gear_ratio] || wtm || R || 97.0 || Gear ratio from rotor to generator. 
+|| [../wind_turbine_parameters#generator_efficiency generator_efficiency] || wtm || R || 0.944 || Electric efficiency of the generator.
+|| [../wind_turbine_parameters#generator_inertia generator_inertia] || wtm || R ||534.116|| Inertia of the generator (in kg/m^2^).
+|| [../wind_turbine_parameters#generator_power_rated generator_power_rated] || wtm || R || 5296610.0 || Rated power of the wind turbine (in W). 
+|| [../wind_turbine_parameters#generator_speed_rated generator_speed_rated] || wtm || R ||1.216.805|| Rated generator speed (in rad/s). 
+|| [../wind_turbine_parameters#generator_torque_max generator_torque_max] || wtm || R || 47402.91 || Maximum Torque of the generator (in Nm). 
+|| [../wind_turbine_parameters#generator_torque_rate_max generator_torque_rate_max] || wtm || R || 15000.0 || Maximum generator torque rate (in Nm/s). 
 || [../salsa#H2SO4_init H2SO4_init] [=#h] || salsa || R || 1.0 || Initial number concentration (in m^-3^) of gaseous sulphuric acid H2SO4 (g). 
 || [../salsa#HNO3_init HNO3_init] || salsa || R || 1.0 || Initial number concentration (in m^-3^) of gaseous nitric acid HNO3 (g). 
+|| [../wind_turbine_parameters#hub_x hub_x] || wtm || R(100) || none || Longitudinal position of the rotor center (in m). 
+|| [../wind_turbine_parameters#hub_y hub_y] || wtm || R(100) || none || Lateral position of the rotor center (in m). 
+|| [../wind_turbine_parameters#hub_z hub_z] || wtm || R(100) || none || Vertical position of the rotor center (in m). This represents the hub height of the turbine. 
 || [../initialization_parameters#humidity humidity]  || ini || L || .F. || Parameter to switch on the prognostic equation for water vapor mixing ratio q. 
 || [../lsmpar#hydraulic_conductivity hydraulic_conductivity] || lsm || R || depends on [../lsmpar#veg_type veg_type] || Hydraulic conductivity of the soil at saturation (in m/s). 
 || [../chempar#icntrl icntrl] [=#i] || chem || I(20) || 0 ||  Selection and steering of the chemistry solver.
-|| [../wind_turbine_par#inertia_gen inertia_gen] || wtm || R ||534.116|| Inertia of the generator (in kg/m^2^). 
-|| [../wind_turbine_par#inertia_rot inertia_rot] || wtm || R || 34784179.0 || Inertia of the rotor (in kg/m^2). 
 || [../initialization_parameters#inflow_damping_height inflow_damping_height] || ini || R || from precursor run || Height below which the turbulence signal is used for turbulence recycling (in m). 
 || [../initialization_parameters#inflow_damping_width inflow_damping_width] || ini || R || 0.1* [../initialization_parameters#inflow_damping_height inflow] \\ [../initialization_parameters#inflow_damping_height _damping_height] || Transition range within which the turbulence signal is damped to zero (in m). 
@@ -310 +316 @@
 || [../agtpar#max_dist_from_path max_dist_from_path] || agt || R ||1.0|| Agent distance from current path section that triggers recalculation of that agent's path (in m).
 || [../flpar#max_elev_change max_elev_change] || vfm || R(100) ||100*0.0|| Maximum possible elevation change in case rate_of_climb is not equal to zero.
-|| [../wind_turbine_par#max_miss max_miss] || wtm || R || 0.08726 || Maximum tolerated yaw misalignment (in rad). 
 || [../chempar#max_street_id max_street_id] || chem || I(99) || 0 ||  Maximum index value for identifying ALL (MAIN and SIDE) streets following street type classes from {{{OpenStreetMap}}}. 
-|| [../wind_turbine_par#max_torque_gen max_torque_gen] || wtm || R || 47402.91 || Maximum Torque of the generator (in Nm). 
-|| [../wind_turbine_par#max_trq_rate max_trq_rate] || wtm || R || 15000.0 || Maximum generator torque rate (in Nm/s). 
 || [../initialization_parameters#mg_cycles mg_cycles] || ini || I ||-1|| Number of cycles to be used with the multigrid scheme. 
 || [../initialization_parameters#mg_switch_to_pe0_level mg_switch_to] \\ [../initialization_parameters#mg_switch_to_pe0_level _pe0_level] || ini || I || see parameter \\ description || Grid level at which data shall be gathered on PE0. 
 || [../lsmpar#min_canopy_resistance min_canopy_resistance] || lsm || R || depends on [../lsmpar#veg_type veg_type] || Minimum canopy (i.e., stomatal) resistance (in s/m). 
-|| [../wind_turbine_par#min_miss min_miss] || wtm || R || 0.008726 || Minimum yaw misalignment for which the actuator stops (in rad). 
 || [../agtpar#min_nr_agent min_nr_agent] || agt || I ||2|| Minimum number of agents for which memory is allocated at every grid cell.
 || [../parpar#min_nr_particles min_nr_particles] || lpm || I ||50|| Minimum number of particles for which memory is allocated at every grid cell. 
-|| [../wind_turbine_par#min_reg15 min_reg15] || wtm || R ||7.016.224|| Lower generator speed boundary of region 1.5 (in rad/s). 
-|| [../wind_turbine_par#min_reg2 min_reg2] || wtm || R ||9.121.091|| Lower generator speed boundary of region 2 [rad/s]. 
 || [../lsmpar#min_soil_resistance min_soil_resistance] || lsm || R || 50.0 || Minimum soil resistance (in s/m). 
 || [../initialization_parameters#mixing_length_1d mixing_length_1d] || ini || C*20 || 'blackadar' || Mixing length used in the 1d-model. 
@@ -329 +329 @@
 || [../agtpar#multi_agent_system_start multi_agent_system_start] || agt || R ||0.0|| Simulation time at which the multi agent system will start excuting (in s).
 || [../chempar#my_steps my_steps] || chem || I(50) || 0 ||  List of fixed timesteps.
+|| [../wind_turbine_parameters#n_airfoils n_airfoils] || wtm || I ||8|| Number of airfoils of the used turbine model. 
 || [../salsa#n_lognorm n_lognorm] [=#n] || salsa || R(7) || 1.04E5, 3.23E4, 5.4, 0.0, 0.0, 0.0, 0.0 || The total aerosol number concentration per aerosol mode (in cm^-3^). 
+|| [../wind_turbine_parameters#n_turbines n_turbines] || wtm || I ||1|| Number of the turbines to be included. Maximum is 100.
 || [../lsmpar#n_vangenuchten n_vangenuchten] || lsm || R || depends on [../lsmpar#soil_type soil_type] || Value of the coefficient n for the calculation of the hydraulic conductivity of soil in the parametrization after Van Genuchten. 
 || [../parpar#na na] || lpm || R(3) || 100.0 || Parameters of initial aerosol spectrum. 
 || [../bcmpar#na_init na_init] || bulkc || R || 100.0E6 || Background dry aerosol concentration. 
-|| [../wind_turbine_par#nairfoils nairfoils] || wtm || I ||8|| Number of airfoils of the used turbine model. 
+|| [../wind_turbine_parameters#nacelle_cd nacelle_cd] || wtm || R(100) || none || Drag coefficient for each nacelle. This parameter needs to be specified for each turbine.
+|| [../wind_turbine_parameters#nacelle_radius nacelle_radius] || wtm || R(100) || none || Radius of the nacelle for each turbine (in m). This parameter has to be non-zero if the nacelle should be included. 
 || [../salsa#nbin nbin] || salsa || I(2) || 3, 7 || Number of aerosol size bins per subrange. 
 || [../bcmpar#nc_const nc_const] || bulkc || R || 70.0E6 || Fixed cloud droplet number density (in 1/m3). 
@@ -361 +364 @@
 || [../initialization_parameters#nsor nsor] || run || I ||20|| Number of iterations to be used with the SOR-scheme. 
 || [../initialization_parameters#nsor_ini nsor_ini] || ini || I ||100|| Initial number of iterations with the SOR algorithm. 
-|| [../wind_turbine_par#nturbines nturbines] || wtm || I ||1|| Number of the turbines to be included. Maximum is 100.
 || [../initialization_parameters#nudging nudging] || ini || L || .F. || Parameter to switch on nudging with data from larger scale models or from measurements.
 || [../parpar#number_concentration number_concentration] || lpm || R || -1.0 || Initial particle number concentration. 
@@ -374 +376 @@
 || [../salsa#OCSV_init OCSV_init] || salsa || R ||1.0|| Initial number concentration (in m^-3^) of gaseous semi-volatile organic compounds. 
 || [../initialization_parameters#omega omega] || ini || R ||7.29E+00|| Angular velocity of the rotating system (in rad s^-1^). 
-|| [../wind_turbine_par#omega_rot omega_rot] || wtm || R(100) || 0.0 || Initial rotational speed for each turbine (in rad s^-1^). 
 || [../initialization_parameters#omega_sor omega_sor] || ini || R || 1.8 || Convergence factor to be used with the SOR-scheme. 
 || [../biometpar#orientation_angle orientation_angle] || biomet || F || 180.0 || Orientation angle of front/face of the human model. 
@@ -389 +390 @@
 || [../parpar#pdy pdy] || lpm || R(10) || 10*dy || Distance along y between particles within a particle source (in m). 
 || [../parpar#pdz pdz] || lpm || R(10) || 10*(zu(2) - zu(1)) || Distance along z between particles within a particle source (in m). 
-|| [../wind_turbine_par#phi_yaw phi_yaw] || wtm || R(100) || none || Yaw angle for each turbine in degrees. A positive yaw means a rotation of the rotor in clockwise direction within the xy-plane. 
 || [../chempar#photolysis_scheme photolysis_scheme] || chem || C*10 || 'simple' ||  Photolysis scheme.
-|| [../wind_turbine_par#pitch_add pitch_add] || wtm || R(100) || 0.0 || Pitch angle for a constant pitch angle (in degrees). 
-|| [../wind_turbine_par#pitch_control pitch_control] || wtm || L || .F. || Parameter to switch on the pitch control. 
-|| [../wind_turbine_par#pitch_rate pitch_rate] || wtm || R || 8.0 || Maximum pitch rate (in degree/s). 
+|| [../wind_turbine_parameters#pitch_angle pitch_angle] || wtm || R(100) || 0.0 || Pitch angle for a constant pitch angle (in degrees). 
+|| [../wind_turbine_parameters#pitch_control pitch_control] || wtm || L || .F. || Parameter to switch on the pitch control. 
+|| [../wind_turbine_parameters#pitch_rate pitch_rate] || wtm || R || 8.0 || Maximum pitch rate (in degree/s). 
 || [../canpar#plant_canopy_transpiration plant_canopy_transpiration] || pcm || L || .F. || Enables calculation of evapotranspiration and corresponding latent heat flux of the resolved plant canopy which utilizes SW and LW radiation fluxes calculated in RTM. 
 || [../sppar#plot_spectra_level plot_spectra_level] || spec || I(100) || No level || Vertical level(s) for which horizontal spectra are to be plotted (in grid points). 
@@ -428 +428 @@
 || [../agtpar#random_start_position_agents random_start_position] \\ [../agtpar#random_start_position_agents _agents] || agt || L ||.T.|| Initial position of the particles is varied randomly within certain limits. 
 || [../flpar#rate_of_climb rate_of_climb] || vfm || R(100) ||100*0.0|| Vertical speed of the aircraft in meter per second. 
-|| [../wind_turbine_par#rated_genspeed rated_genspeed] || wtm || R ||1.216.805|| Rated generator speed (in rad/s). 
-|| [../wind_turbine_par#rated_power rated_power] || wtm || R || 5296610.0 || Rated power of the wind turbine (in W). 
 || [../initialization_parameters#rayleigh_damping_factor rayleigh_damping] \\ [../initialization_parameters#rayleigh_damping_factor _factor] || ini || R || 0.0 and/or 0.01 || Factor for Rayleigh damping. 
 || [../initialization_parameters#rayleigh_damping_height rayleigh_damping] \\ [../initialization_parameters#rayleigh_damping_height _height] || ini || R || 2/3*zu(nz) || Height where the Rayleigh damping starts (in m). 
 || [../chempar#rcntrl rcntrl] || chem || R(20) || 0.0 ||  Steering of the chemistry solver. 
-|| [../wind_turbine_par#rcx rcx] || wtm || R(100) || none || Longitudinal position of the rotor center (in m). 
-|| [../wind_turbine_par#rcy rcy] || wtm || R(100) || none || Lateral position of the rotor center (in m). 
-|| [../wind_turbine_par#rcz rcz] || wtm || R(100) || none || Vertical position of the rotor center (in m). This represents the hub height of the turbine. 
+|| [../wind_turbine_parameters#region_15_min region_15_min] || wtm || R ||7.016.224|| Lower generator speed boundary of region 1.5 (in rad/s). 
+|| [../wind_turbine_parameters#region_2_min region_2_min] || wtm || R ||9.121.091|| Lower generator speed boundary of region 2 [rad/s]. 
 || [../agtpar#read_agents_from_restartfile read_agents_from] \\ [../agtpar#read_agents_from_restartfile _restartfile] || agt || L ||.F.|| Flag to read agent data from restart file.
 || [../parpar#read_particles_from_restartfile read_particles_from] \\ [../parpar#read_particles_from_restartfile _restartfile] || lpm || L || .T. || Read particle data from the previous run. 
@@ -442 +439 @@
 || [../initialization_parameters#reference_state reference_state] || ini || C*20 || '' 'initial_profile' '' || Defines what is used as reference state in the buoyancy term. 
 || [../userpar#region region] || user || C*40(0:9) |||| Name(s) of the subdomain(s) defined by the user. 
+|| [../wind_turbine_parameters#region_2_slope region_2_slope] || wtm || R ||2.332.287|| Slope constant for region 2. 
 || [../salsa#reglim reglim]  || salsa || R(3) || 3.0E-9, 5.0E-8, 1.0E-5  || Aerosol diameter limits for the subranges (in m) in the following order: lower limit of 1, upper limit of 1 and lower limit of 2, upper limit of 2. 
 || [../agtpar#repuls_agent repuls_agent] || agt || R ||1.5|| Magnitude of the repulsive force agents exert on each other (in m^2^ s^-2^).
@@ -448 +446 @@
 || [../lsmpar#residual_moisture residual_moisture] || lsm || R || depends on [../lsmpar#soil_type soil_type] || Residual soil moisture content (in m³/m³). 
 || [../d3par#restart_time restart_time] || run || R || 9999999.9 || Simulated time after which a restart run is to be carried out (in s). 
-|| [../parpar#rm rm]|| lpm || R(3) || 0.05E-6 || Parameters of initial aerosol spectrum. 
-|| [../wind_turbine_par#rnac rnac] || wtm || R(100) || none || Radius of the nacelle for each turbine (in m). This parameter has to be non-zero if the nacelle should be included. 
+|| [../parpar#rm rm]|| lpm || R(3) || 0.05E-6 || Parameters of initial aerosol spectrum.
 || [../lsmpar#root_fraction root_fraction] || lsm || R(4) || depends on [../lsmpar#veg_type veg_type] || Root distribution over the four soil layers. 
 || [../initialization_parameters#roughness_length roughness_length] || ini || R || 0.1 || Roughness length (in m). 
-|| [../wind_turbine_par#rr rr] || wtm || R(100) ||63|| Radius of the rotor (in m). 
+|| [../wind_turbine_parameters#rotor_inertia rotor_inertia] || wtm || R || 34784179.0 || Inertia of the rotor (in kg/m^2). 
+|| [../wind_turbine_parameters#rotor_radius rotor_radius] || wtm || R(100) ||63|| Radius of the rotor (in m). 
+|| [../wind_turbine_parameters#rotor_speed rotor_speed] || wtm || R(100) || 0.0 || Initial rotational speed for each turbine (in rad s^-1^). 
 || [../initialization_parameters#s_surface s_surface] [=#s] || ini || R || 0.0 || Surface value of the passive scalar (in kg m^-3^ or ppm). 
 || [../initialization_parameters#s_surface_initial_change s_surface_initial] \\ [../initialization_parameters#s_surface_initial_change _change] || ini || R || 0.0 || Change in surface scalar concentration to be made at the beginning of the 3d run (in kg m^-3^ or ppm). 
@@ -470 +469 @@
 || [../d3par#section_yz section_yz] || run || I(100) || no section || Position of cross section(s) for output of 2d (yz) vertical cross sections (grid point index i). 
 || [../parpar#seed_follows_topography seed_follows_topography] || lpm || L || .F. || Heights of initial particles are interpreted relative to the given topography. 
-|| [../wind_turbine_par#segment_length segment_length] || wtm || R || 1.0 || Length of each rotor segment the rotor area is divided into, in tangential direction, as factor of the grid spacing. 
-|| [../wind_turbine_par#segment_width segment_width] || wtm || R || 0.5 || Length of each rotor segment the rotor area is divided into, in radial direction, as factor of the grid spacing. 
+|| [../wind_turbine_parameters#segment_length_tangential segment_length_tangential] || wtm || R || 1.0 || Length of each rotor segment the rotor area is divided into, in tangential direction, as factor of the grid spacing. 
+|| [../wind_turbine_parameters#segment_width_radial segment_width_radial] || wtm || R || 0.5 || Length of each rotor segment the rotor area is divided into, in radial direction, as factor of the grid spacing. 
 || [../chempar#side_street_id side_street_id] || chem || I(99) || 0 ||  Index for identifying SIDE streets following street type classes from !OpenStreetMap. 
 || [../bcmpar#sigma_bulk sigma_bulk] || bulkc || R || 2.0 || The dispersion of the dry aerosol spectrum. 
@@ -489 +488 @@
 || [../d3par#skip_time_do2d_yz skip_time_do2d_yz] || run || R || value of [../d3par#skip_time_data_output skip_time] \\ [../d3par#skip_time_data_output _data_output] || No output of instantaneous vertical (yz) cross section data before this interval has passed (in s). 
 || [../d3par#skip_time_do3d skip_time_do3d] || run || R || value of [../d3par#skip_time_data_output skip_time] \\ [../d3par#skip_time_data_output _data_output] || No output of instantaneous 3d volume data before this interval has passed (in s). 
-|| [../wind_turbine_par#slope2 slope2] || wtm || R ||2.332.287|| Slope constant for region 2. 
 || [../lsmpar#soil_moisture soil_moisture] || lsm || R(4) || 4*0.0 || Soil moisture distribution over the four soil layers. 
 || [../lsmpar#soil_temperature soil_temperature] || lsm || R(5) || see description || Soil temperature distribution over the four soil layers (in K). 
@@ -495 +493 @@
 || [../sppar#spectra_direction spectra_direction] || spec || C*2(10) || 10*' ' || Direction(s) along which spectra are to be calculated. 
 || [../flpar#speed_agl speed_agl] || vfm || R(100) ||100*25.0|| Horizontal speed of the aircraft above ground level in meter per second. 
-|| [../wind_turbine_par#speed_control speed_control] || wtm || L || .F. || Parameter to switch on the speed control. 
+|| [../wind_turbine_parameters#speed_control speed_control] || wtm || L || .F. || Parameter to switch on the speed control. 
 || [../initialization_parameters#spinup_pt_amplitude spinup_pt_amplitude] || ini || R || 0.0 || Representative amplitude of the diurnal near-surface temperature variation during the spinup phase. 
 || [../initialization_parameters#spinup_pt_mean spinup_pt_mean] || ini || R || [value of] [pt_surface] || Mean near-surface air temperature during the spinup phase (see spinup_time). 
@@ -519 +517 @@
 || [../d3par#termination_time_needed termination_time_needed] || run || R || 35.0 || CPU time needed for terminal actions at the end of a run in batch mode (in s). 
 || [../biometpar#thermal_comfort thermal_comfort] || biomet || L || .F. || Switch the calculation of all three thermal comfort indices off (.F.) or on (.T.). 
-|| [../wind_turbine_par#tilt tilt] || wtm || R || 0.0 || Rotor tilt of the rotor plane (in degrees). 
+|| [../wind_turbine_parameters#tilt_angle tilt_angle] || wtm || R || 0.0 || Rotor tilt_angle of the rotor plane (in degrees). 
 || [../chempar#time_fac_type time_fac_type] || chem || C*80 || MDH ||  Type of time treatment for DEFAULT mode of the chem_emission module. 
-|| [../wind_turbine_par#time_turbine_on time_turbine_on] || wtm || R || 0.0 || Simulation time at which the turbines are switched on. 
+|| [../wind_turbine_parameters#time_turbine_on time_turbine_on] || wtm || R || 0.0 || Simulation time at which the turbines are switched on. 
 || [../radpar#time_utc_init time_utc_init] || rrtmg || R || 43200.0 || UTC time at model start in seconds starting from midnight. 
 || [../initialization_parameters#timestep_scheme timestep_scheme] || ini || C*20 || 'runge-kutta-3' || Time step scheme to be used for integration of the prognostic variables. 
+|| [../wind_turbine_parameters#tip_loss_correction] || wtm || L || .F. || Parameter to switch on the tip loss correction.
 || [../initialization_parameters#topography topography] || ini || C*40 || 'flat' || Topography mode. 
 || [../initialization_parameters#topography_grid_convention topography_grid] \\ [../initialization_parameters#topography_grid_convention _convention] || ini || C*11 || default depends on \\ value of [../initialization_parameters#topography topography] || Convention for defining the topography grid. 
@@ -531 +530 @@
 || [../oceanpar#top_salinityflux top_salinityflux] || ocean || R || no prescribed \\ salinityflux || Kinematic salinity flux at the top boundary, i.e. the sea surface (in psu m/s). 
 || [../initialization_parameters#top_scalarflux top_scalarflux] || ini || R || no prescribed \\ scalarflux || Scalar flux at the top surface (in kg m^-2^ s^-1^ or ppm m s^-1^). 
+|| [../wind_turbine_parameters#tower_cd tower_cd] || wtm || R(100) || none ||Drag coefficient for each tower. This parameter needs to be specified for each turbine.
+|| [../wind_turbine_parameters#tower_diameter tower_diameter] || wtm || R(100) || none || Diameter of the tower of the wind turbine used below the rotor. This parameter has to be non-zero if a tower should be included. The parameter needs to be specified for every turbine separately. 
 || [../initialization_parameters#transpose_compute_overlap transpose_compute] \\ [../initialization_parameters#transpose_compute_overlap _overlap] || ini || L || .F. || Parameter to switch on parallel execution of fft and transpositions (with MPI_ALLTOALL). 
 || [../initialization_parameters#tunnel_height tunnel_height] || ini || R || 0.2*nz || Height of outer-wall tunnel top. 
@@ -579 +580 @@
 || [../flpar#y_end y_end] [=#y] || vfm || R(100) || 100*999999999.0 || End-position of the flight leg along y in meter. 
 || [../flpar#y_start y_start] || vfm || R(100) || 100*999999999.0 || Start-position of the flight leg along y in meter. 
-|| [../wind_turbine_par#yaw_control yaw_control] || wtm || L || .F. || Parameter to switch on the yaw controller. 
-|| [../wind_turbine_par#yaw_speed yaw_speed] || wtm || R || 0.005236 || Speed of the yaw actuator (in rad/s). 
+|| [../wind_turbine_parameters#yaw_angle yaw_angle] || wtm || R(100) || none || Yaw angle for each turbine in degrees. A positive yaw means a rotation of the rotor in clockwise direction within the xy-plane. 
+|| [../wind_turbine_parameters#yaw_control yaw_control] || wtm || L || .F. || Parameter to switch on the yaw controller. 
+|| [../wind_turbine_parameters#yaw_misalignment_max yaw_misalignment_max] || wtm || R || 0.08726 || Maximum tolerated yaw misalignment (in rad). 
+|| [../wind_turbine_parameters#yaw_misalignment_min yaw_misalignment_min] || wtm || R || 0.008726 || Minimum yaw misalignment for which the actuator stops (in rad). 
+|| [../wind_turbine_parameters#yaw_speed yaw_speed] || wtm || R || 0.005236 || Speed of the yaw actuator (in rad/s). 
 || [../initialization_parameters#y_shift y_shift] || ini || I ||0|| Distance of y-shift for cyclic and non-cyclic boundary conditions (in number of PEs). 
 || [../lsmpar#z0_eb z0_eb] [=#z] || lsm || R || depends on [../lsmpar#veg_type veg_type] || Roughness length for momentum (in m). 
@@ -589 +593 @@
 || [../initialization_parameters#zeta_min zeta_min] || ini || R || -9990.0 || Lower limit of the stability parameter {{{zeta = z_mo/L}}}. 
 || [../lsmpar#zs zs] || lsm || R(4) || see description || Depths of the four soil layers (in m). 
+