Home

Context Navigation

parlist

Timestamp:: May 25, 2018 10:52:46 AM (7 years ago)
Author:: scharf
Comment:: --

Legend:

: Unmodified
: Added
: Removed
: Modified

doc/app/parlist

-                      v219
+                      v220
 || [../parpar#aero_type aero_type] || lpm ||  || C*15 || 'maritime' || Define a aerosol spectrum using three log-normal distributions. ||
 || [../parpar#aero_weight aero_weight] || lpm ||  || R || 1.0 || Scale the number concentration defined by aero_type. ||
+|| [../parpar#aerosol_bulk aerosol_bulk] || lpm || || C*20 || 'nacl' || Parameter to choose the used aerosol type. ||
 || [../wind_turbine_par#air_dens air_dens] [=#a] || wtm || || R || 1.225 || The air density (in kg/m^3^) is necessary to convert the aerodynamic torque of the rotor into a power (in W). ||
 || [../radpar#albedo albedo] || rrtmg ||  || R || 0.2 || Surface albedo. ||
 …
 || [../parpar#alloc_factor alloc_factor] || lpm || || R || 20.0 || Factor (in percent) describing the memory allocated additionally to the memory needed for initial particles at a given grid cell. ||
 || [../canpar#alpha_lad alpha_lad] || pcm ||  || R || 9999999.9 || Coefficient for constructing leaf area density profile. ||
+|| [../inipar#alpha_surface alpha_surface] || ini || Others || R || 0.0 || Inclination of the model domain with respect to the horizontal (in degrees). ||
 || [../lsmpar#alpha_vangenuchten alpha_vangenuchten] || lsm ||  || R || depends on [../lsnpar#soil_type soil_type] || Value of the coefficient alpha for the calculation of the hydraulic conductivity of soil in the parametrization after Van Genuchten ||
 || [../inipar#alpha_surface alpha_surface] || ini || Others || R || 0.0 || Inclination of the model domain with respect to the horizontal (in degrees). ||
+||[../inipar#approximation approximation] || ini || || C*20 || 'boussinesq' || Parameter to choose the approximation of the model equations. ||
 || [../d3par#averaging_interval averaging_interval] || run || Data output || R || 0.0 || Averaging interval for all output of temporally averaged data (in s). ||
 || [../d3par#averaging_interval_pr averaging_interval_pr] || run || Data output || R || value of [../d3par#averaging_interval averaging_interval] || Averaging interval for vertical profiles output to local file [../iofiles#DATA_1D_PR_NETCDF DATA_1D_PR_NETCDF] (in s). ||
 …
 || [../inipar#bc_q_t bc_q_t] || ini || Boundary conditions || C*20 || 'neumann' || Top boundary condition of the water vapor / total water mixing ratio. ||
 || [../inipar#bc_s_b bc_s_b] || ini || Boundary conditions || C*20 || 'dirichlet' || Bottom boundary condition of the scalar concentration.  ||
 || [../inipar#bc_s_t bc_st] || ini || Boundary conditions || C*20 || 'neumann' || Top boundary condition of the scalar concentration.  ||
+|| [../inipar#bc_s_t bc_s_t] || ini || Boundary conditions || C*20 || 'neumann' || Top boundary condition of the scalar concentration.  ||
 || [../inipar#bc_sa_t bc_sa_t] || ini || Boundary conditions || C*20 || 'neumann' || Top boundary condition of the salinity.  ||
 || [../inipar#bc_uv_b bc_uv_b] || ini || Boundary conditions || C*20 || 'dirichlet' || Bottom boundary condition of the horizontal wind components u and v. ||
 …
 || [../d3par#cthf cthf] || ini ||  || R || 0.0 || Average heat flux that is prescribed at the top of the plant canopy (in K m/s). ||
 || [../parpar#curvature_solution_effects curvature_solution] \\ [../parpar#curvature_solution_effects _effects] || lpm || || L || .F. || Parameter to consider solution and curvature effects on the equilibrium vapor pressure of cloud droplets. ||
+|| [../parpar#curvature_solution_effects_bulk curvature_solution] \\ [../parpar#curvature_solution_effects_bulk _effects_bulk] || lpm || || L || .F. || Parameter to switch on an activation scheme which considers curvature and solution effects of cloud droplet activation. ||
 || [../inipar#cycle_mg cycle_mg] || ini || Numerics || C*1 || 'w' || Type of cycle to be used with the multi-grid method. ||
 || [../inipar#damp_level_1d damp_level_1d] [=#d] || ini || Initialization || R || zu(nz + 1) || Height where the damping layer begins in the 1d-model (in m). ||
 || [../d3par#data_output data_output] || run || Data output || C*10(100) || 100*' ' || Quantities for which 2d cross section and/or 3d volume data are to be output. ||
+|| [../d3par#data_output_2d_on_each_pe data_output_2d_on] \\ [../d3par#data_output_2d_on_each_pe _each_pe] || run || Data output || L || .T. || Output 2d cross section data by one or all processors.  ||
+|| [../d3par#data_output_during_spinup data_output] \\ [../d3par#data_output_during_spinup _during_spinup] || ini || Initialization || L || .F. || Parameter for switching on data output in the spinup phase (see spinup_time). ||
 || [../d3par#data_output_masks data_output_masks] || run || Data output || C*10 \\ (max_masks, \\ 100) || max_masks*100*' ' || Quantities for which masked data are to be output. ||
+|| [../userpar#data_output_masks_user data_output_masks_user] || user || || C*10 \\ (max_masks, \\ 100) || max_masks*100*' ' || User-defined quantities for which masked data are to be output. ||
 || [../d3par#data_output_pr data_output_pr] || run || Data output || C*10(100) || 100*' ' || Quantities for which vertical profiles (horizontally averaged) are to be output. ||
 || [../d3par#data_output_pr_user data_output_pr_user] || user || Data output || C*10(200) || 200*' ' || User defined quantities for which horizontally averaged profile data is to be output. ||
 ||[../sppar#data_output_sp data_output_sp] || spec || ||C*10(10)|| 10*' ' ||Quantities for which horizontal spectra are to be calculated and output.
 || [../userpar#data_output_user data_output_user] || user || Data output || C*10(100) || 100*' ' || User defined quantities for which 2d cross section and/or 3d volume data are to be output. ||
+|| [../d3par#data_output_2d_on_each_pe data_output_2d_on] \\ [../d3par#data_output_2d_on_each_pe _each_pe] || run || Data output || L || .T. || Output 2d cross section data by one or all processors.  ||
+|| [../radpar#day_init day_init] || rrtmg ||  || I || 172 || Day of the year at model start. ||
+|| [../radpar#day_of_year_init day_of_year_init] || ini||  || I || 172 || Day of the year at model start. ||
 || [../parpar#density_ratio density_ratio] || lpm || || R(10) || 0.0, 9*9999999.9 || Ratio of the density of the fluid and the density of the particles. ||
 || [../parpar#dissipation_classes dissipation_classes] || lpm || || I ||10|| Number of dissipation classes to be used in the collision efficiency table. ||
 …
 || [../inipar#dp_level_b dp_level_b] || run || Mode || R || 0.0 || Lower limit of the vertical range for which the external pressure gradient is applied (in m). ||
 || [../inipar#dpdxy dpdxy] || run || Mode || R(2) || 2*0.0 || Values of the external pressure gradient applied in x- and y-direction, respectively (in Pa/m). ||
+|| [../inipar#dry_aerosol_radius dry_aerosol_radius] || ini || || R || 0.05E-6 || The mean geometric radius of the dry aerosol spectrum. ||
 || [../d3par#dt dt] || run || Run steering || R || variable || Time step for the 3d-model (in s). ||
 || [../d3par#dt_averaging_input dt_averaging_input] || run || Data output || R || 0.0 || Temporal interval of data which are subject to temporal averaging (in s). ||
 …
 || [../d3par#dt_do2d_yz dt_do2d_yz] || run || Data output || R || value of \\ [../d3par#dt_data_output dt_data_output] || Temporal interval at which vertical cross section data (yz) shall be output (in s). ||
 || [../d3par#dt_do3d dt_do3d] || run || Data output || R || value of \\ [../d3par#dt_data_output dt_data_output] || Temporal interval at which 3d volume data shall be output (in s). ||
 || [../dvrpar#dt_dvr dt_dvr] || dvr || || R || 9999999.9 || Temporal interval of scenes to be displayed with the dvrp software (in s). ||
+|| [../dvrpar#dt_dvrp dt_dvrp] || dvr || || R || 9999999.9 || Temporal interval of scenes to be displayed with the dvrp software (in s). ||
 || [../d3par#dt_max dt_max] || run || Run steering || R || 20.0 || Maximum allowed value of the timestep (in s). ||
 || [../parpar#dt_min_part dt_min_part] || lpm || || R || 0.0002 || Minimum value for the particle timestep when SGS velocities are used (in s). ||
 …
 || [../d3par#dt_run_control dt_run_control] || run || Data output || R || 60.0 || Temporal interval at which run control output is to be made (in s). ||
 || [../inipar#dt_run_control_1d dt_run_control_1d] || ini || Initialization || R || 60.0 || Temporal interval of runtime control output of the 1d-model (in s). ||
 || [../parpar#dt_sort_particles dt_sort_particles] || lpm || || R || 0.0 || Temporal interval for sorting particles (in s). '''Not available from release 4.0 on.''' ||
+|| [../parpar#dt_spinup dt_spinup] || ini || || R || 60.0 || Time step during integration of the land surface, urban surface, and radiation models during the spinup phase.  ||
 || [../parpar#dt_write_particle_data dt_write_particle] \\ [../parpar#dt_write_particle_data _data] || lpm || || R || 9999999.9 || Temporal interval for output of particle data (in s). ||
 || [../wind_turbine_par#dtow dtow] || wtm || || R(100) || none || Diameter of the tower of the wind turbine used below the rotor. This parameter has to be non-zero if a tower should be included. The parameter needs to be specified for every turbine separately. ||
 …
 || [../lsmpar#field_capacity field_capacity] || lsm ||  || R || depends on [../lsmpar#soil_type soil_type] || Soil moisture at field capacity (in m³/m³). ||
 || [../inipar#fft_method fft_method]  || ini || Numerics || C*20 || 'system specific' || FFT-method to be used. ||
+|| [../inipar#flux_input_mode flux_input_mode] || ini || || C*40 || 'approximation-specific' || Parameter to choose the flux unit for input data. ||
+|| [../inipar#flux_output_mode flux_output_mode] || ini || || C*40 || 'approximation-specific' || Parameter to choose the flux unit for outputdata. ||
 || [../d3par#force_print_header force_print_header] || run || Data output || L || .F. || Steering of header output to the local file [../iofiles#RUN_CONTROL RUN_CONTROL]. ||
 || [../inipar#galilei_transformation galilei_transformation] [=#g] || ini || Mode || L || .F. || Application of a Galilei-transformation to the coordinate system of the model. ||
 …
 || [../inipar#nc_const nc_const] || ini || Cloud physics || R || 70.0E6 || Cloud droplet number density (in m-3). ||
 || [../parpar#na na] || lpm || || R(3) || 100.0 || Parameters of initial aerosol spectrum. ||
+|| [../inipar#na_init na_init] || ini || || R || 100.0E6 || Background dry aerosol concentration. ||
 || [../nestpar#nesting_datatransfer_mode nesting_datatransfer_mode] || nest || || C*7 || 'mixed' || Type of nesting data transfer mode. ||
 || [../nestpar#nesting_mode nesting_mode] || nest || || C*7 || 'two-way' || Type of nesting mode. ||
 …
 || [../wind_turbine_par#omega_rot omega_rot] || wtm ||  || R(100) || 0.0 || Initial rotational speed for each turbine (in rad s^-1^). ||
 || [../inipar#omega_sor omega_sor] || ini || Numerics || R || 1.8 || Convergence factor to be used with the SOR-scheme. ||
 || [../inipar#outflow_damping_width outflow_damping] \\ [../inipar#outflow_damping_width _width] || ini || Boundary conditions || I || MIN(20, nx/2 or ny/2) || Width of the damping range in the vicinity of the outflow (gridpoints). ||
+|| [../inipar#outflow_source_plane outflow_source] \\ [../inipar#outflow_source_plane _plane] || ini || Boundary conditions || R ||  || Position of the vertical source plane from where instantaneous values of u, v, w, pt, q, s, and e are copied to the outflow boundary. ||
 || [../parpar#particles_per_point particles_per_point] [=#p] || lpm || || I ||1|| Number of particles to be started per point. ||
 || [../parpar#particle_advection_start particle_advection] \\ [../parpar#particle_advection_start _start] || lpm || || R || 0.0 || Time of the first release of particles (in s). ||
 …
 || [../wind_turbine_par#segment_length segment_length] || wtm ||  || R || 1.0 || Length of each rotor segment the rotor area is divided into, in tangential direction, as factor of the grid spacing. ||
 || [../wind_turbine_par#segment_width segment_width] || wtm ||  || R || 0.5 || Length of each rotor segment the rotor area is divided into, in radial direction, as factor of the grid spacing. ||
+|| [../inipar#sigma_bulk sigma_bulk] || ini || || R || 2.0 || The dispersion of the dry aerosol spectrum. ||
 || [../d3par#skip_time_data_output skip_time_data_output] || run || Data output || R || 0.0 || No data output before this interval has passed (in s). ||
 || [../d3par#skip_time_data_output_av skip_time_data] \\ [../d3par#skip_time_data_output_av _output_av] || run || Data output || R || value of [../d3par#skip_time_data_output skip_time] \\ [../d3par#skip_time_data_output _data_output] || No output of temporally averaged 2d/3d data before this interval has passed (in s). ||
 …
 || [../dvrpar#slicer_range_limits_dvrp slicer_range] \\ [../dvrpar#slicer_range_limits_dvrp _limits_dvrp] || dvr || || R(2,10) || 10*(-1,1) || Ranges of values to which a color table has to be mapped (units of the respective quantity). ||
 || [../wind_turbine_par#slope2 slope2] || wtm ||  || R || 2.332287 || Slope constant for region 2. ||
-|| [../sppar#spectra_direction spectra_direction] || spec || || C*2(10) || 10*' ' || Direction(s) along which spectra are to be calculated. ||
-|| [../wind_turbine_par#speed_control speed control] || wtm ||  || L || .F. || Parameter to switch on the speed control. ||
 || [../lsmpar#soil_moisture soil_moisture] || lsm ||  || R(4) || 4*0.0 || Soil moisture distribution over the four soil layers. ||
 || [../lsmpar#soil_temperature soil_temperature] || lsm ||  || R(5) || see description || Soil temperature distribution over the four soil layers (in K). ||
 || [../lsmpar#soil_type soil_type] || lsm ||  || I || 3 || Soil type to be used in the soil model. ||
+|| [../sppar#spectra_direction spectra_direction] || spec || || C*2(10) || 10*' ' || Direction(s) along which spectra are to be calculated. ||
+|| [../wind_turbine_par#speed_control speed_control] || wtm ||  || L || .F. || Parameter to switch on the speed control. ||
+|| [../inipar#spinup_pt_amplitude spinup_pt_amplitude] || ini || || R || 0.0 || Representative amplitude of the diurnal near-surface temperature variation during the spinup phase. ||
+|| [../inipar#spinup_pt_mean spinup_pt_mean] || ini || || R || [value of] [pt_surface] || Mean near-surface air temperature during the spinup phase (see spinup_time). ||
+|| [../inipar#spinup_time spinup_time] || ini || || R || 0.0 || Parameter for steering of the spinup time. ||
 || [../inipar#statistic_regions statistic_regions] || ini || Others|| I ||0|| Number of additional user-defined subdomains for which statistical analysis and corresponding output (profiles, time series) shall be made. ||
 || [../inipar#subs_vertical_gradient subs_vertical_gradient] || ini || Mode || R(10) || 10*0.0 || Gradient(s) of the profile for the large scale subsidence/ascent velocity (in (m/s) / 100 m). ||
 …
 || [../inipar#top_momentumflux_v top_momentumflux_v] || ini || Boundary conditions || R || no prescribed momentumflux || Momentum flux along y at the top boundary (in m^2^/s^2^). ||
 || [../inipar#top_salinityflux top_salinityflux] || ini || Boundary conditions || R || no prescribed \\ salinityflux || Kinematic salinity flux at the top boundary, i.e. the sea surface (in psu m/s). ||
+|| [../inipar#top_scalarflux top_scalarflux] || ini || Boundary conditions || R || no prescribed \\ scalarflux|| Scalar flux at the top surface. ||
 || [../inipar#transpose_compute_overlap transpose_compute] \\ [../inipar#transpose_compute_overlap _overlap] || ini || Numerics || L || .F. || Parameter to switch on parallel execution of fft and transpositions (with MPI_ALLTOALL). ||
 || [../inipar#tunnel_height tunnel_height] || ini || Topography || R || 0.2*nz || Height of outer-wall tunnel top. ||
 …
 || [../inipar#tunnel_wall_depth tunnel_wall_depth] || ini || Topography || R || max( dx, dy, dz ) || Depth of tunnel walls. ||
 || [../inipar#turbulent_inflow turbulent_inflow] || ini || Boundary conditions || L || .F. || Generates a turbulent inflow at side boundaries using a turbulence recycling method. ||
+|| [../inipar#turbulent_outflow turbulent_outflow] || ini || Boundary conditions || L || .F. || Generates a turbulent outflow at side boundaries using a turbulence recycling method. ||
 || [../inipar#u_bulk u_bulk] [=#u] || ini || Mode || R || 0.0 || u-component of the predefined bulk velocity (in m/s). ||
 || [../inipar#u_profile u_profile] || ini || Initialization || R(100) || 100 * 9999999.9 || Values of u-velocity component to be used as initial profile (in m/s). ||