Changes between Version 48 and Version 49 of doc/app/spectra_parameters

Timestamp:

Feb 24, 2021 3:25:57 PM (4 years ago)

Author:

wagner

Comment:

--

doc/app/spectra_parameters

@@ -16 +16 @@
 }}}
 {{{#!td style="vertical-align:top; width: 75px"
-value of \\ [../d3par#averaging_interval averaging] \\ [../d3par#averaging_interval _interval]
+value of \\ [../runtime_parameters#averaging_interval averaging] \\ [../runtime_parameters#averaging_interval _interval]
 }}}
 {{{#!td
 Averaging interval for spectra output to local file [../iofiles#DATA_1D_SP_NETCDF DATA_1D_SP_NETCDF] (in s). \\\\
 If this parameter is given a non-zero value, temporally averaged spectra data are output. By default, spectra data are not subject to temporal averaging. The interval length is limited by the parameter [#dt_dosp dt_dosp]. In any case '''averaging_interval_sp <= dt_dosp''' must hold. \\\\
-If an interval is defined, then by default the average is calculated from the data values of all time steps lying within this interval. The number of time levels entering into the average can be reduced with the parameter [../d3par#dt_averaging_input_pr dt_averaging_input_pr]. \\\\
+If an interval is defined, then by default the average is calculated from the data values of all time steps lying within this interval. The number of time levels entering into the average can be reduced with the parameter [../runtime_parameters#dt_averaging_input_pr dt_averaging_input_pr]. \\\\
 If an averaging interval can not be completed at the end of a run, it will be finished at the beginning of the next restart run. Thus for restart runs, averaging intervals do not necessarily begin at the beginning of the run.
 }}}
@@ -69 +69 @@
 }}}
 {{{#!td style="vertical-align:top"
-value of \\ [../d3par#dt_data_output dt_data] \\ [../d3par#dt_data_output _output]
+value of \\ [../runtime_parameters#dt_data_output dt_data] \\ [../runtime_parameters#dt_data_output _output]
 }}}
 {{{#!td
 Temporal interval at which spectra data shall be output (in s). \\\\
-If output of horizontal spectra is switched on (see [#data_output_sp data_output_sp]), this parameter can be used to assign the temporal interval at which spectral data shall be output. Output can be skipped at the beginning of a simulation using parameter [#skip_time_dosp skip_time_dosp], which has zero value by default. Reference time is the beginning of  the simulation, i.e. output takes place at times t = '''skip_time_dosp''' + '''dt_dosp''', '''skip_time_dosp''' + '''2*dt_dosp''', '''skip_time_dosp''' + '''3*dt_dosp''', etc. The actual output times can deviate from these theoretical values (see [../d3par#dt_dopr dt_dopr]).  If '''dt_dosp''' < [../d3par#dt dt], then spectral data are output after each time step (if this is requested it should be '''dt_dosp''' = 0). 
+If output of horizontal spectra is switched on (see [#data_output_sp data_output_sp]), this parameter can be used to assign the temporal interval at which spectral data shall be output. Output can be skipped at the beginning of a simulation using parameter [#skip_time_dosp skip_time_dosp], which has zero value by default. Reference time is the beginning of  the simulation, i.e. output takes place at times t = '''skip_time_dosp''' + '''dt_dosp''', '''skip_time_dosp''' + '''2*dt_dosp''', '''skip_time_dosp''' + '''3*dt_dosp''', etc. The actual output times can deviate from these theoretical values (see [../runtime_parameters#dt_dopr dt_dopr]).  If '''dt_dosp''' < [../runtime_parameters#dt dt], then spectral data are output after each time step (if this is requested it should be '''dt_dosp''' = 0). 
 }}}
 |----------------
@@ -83 +83 @@
 }}}
 {{{#!td style="vertical-align:top"
-value of \\ [../d3par#skip_time_data_output skip_time] \\ [../d3par#skip_time_data_output _data_output]
+value of \\ [../runtime_parameters#skip_time_data_output skip_time] \\ [../runtime_parameters#skip_time_data_output _data_output]
 }}}
 {{{#!td