Home

Context Navigation

source: palm/trunk/SOURCE/parin.f90 @ 4186

Last change on this file since 4186 was 4183, checked in by oliver.maas, 5 years ago
simplified steering of recycling of absolute values. Replaced initialization parameter recycle_absolute_quantities by recycling_method_for_thermodynamic_quantities.
Property svn:keywords set to `Id`
File size: 34.9 KB

Line
1	!> @file parin.f90
2	!------------------------------------------------------------------------------!
3	! This file is part of the PALM model system.
4	!
5	! PALM is free software: you can redistribute it and/or modify it under the
6	! terms of the GNU General Public License as published by the Free Software
7	! Foundation, either version 3 of the License, or (at your option) any later
8	! version.
9	!
10	! PALM is distributed in the hope that it will be useful, but WITHOUT ANY
11	! WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR
12	! A PARTICULAR PURPOSE. See the GNU General Public License for more details.
13	!
14	! You should have received a copy of the GNU General Public License along with
15	! PALM. If not, see <http://www.gnu.org/licenses/>.
16	!
17	! Copyright 1997-2019 Leibniz Universitaet Hannover
18	!------------------------------------------------------------------------------!
19	!
20	! Current revisions:
21	! -----------------
22	!
23	!
24	! Former revisions:
25	! -----------------
26	! $Id: parin.f90 4183 2019-08-23 07:33:16Z suehring $
27	! replaced recycle_absolute_quantities by recycling_method_for_thermodynamic_quantities
28	!
29	! 4182 2019-08-22 15:20:23Z scharf
30	! Corrected "Former revisions" section
31	!
32	! 4176 2019-08-20 14:10:41Z oliver.maas
33	! added recycle_absolute_quantities to initialization_parameters namelist
34	!
35	! 4173 2019-08-20 12:04:06Z gronemeier
36	! add vdi_internal_controls
37	!
38	! 4131 2019-08-02 11:06:18Z monakurppa
39	! Allocate hom and hom_sum to allow profile output for salsa variables.
40	!
41	! 4079 2019-07-09 18:04:41Z suehring
42	! +monotonic_limiter_z
43	!
44	! 4022 2019-06-12 11:52:39Z suehring
45	! Change default top boundary condition for pressure to Neumann in offline
46	! nesting case
47	!
48	! 4017 2019-06-06 12:16:46Z schwenkel
49	! Introduce alternative switch for debug output during timestepping
50	!
51	! 3885 2019-04-11 11:29:34Z kanani
52	! Changes related to global restructuring of location messages and introduction
53	! of additional debug messages
54	!
55	! 3806 2019-03-21 12:45:50Z raasch
56	! additional check for lateral boundary conditions added
57	!
58	! 3747 2019-02-16 15:15:23Z gronemeier
59	! removed setting of parameter region
60	!
61	! 3746 2019-02-16 12:41:27Z gronemeier
62	! Removed most_method
63	!
64	! 3649 2019-01-02 16:52:21Z suehring
65	! Delete debug-print statements
66	!
67	! Revision 1.1 1997/07/24 11:22:50 raasch
68	! Initial revision
69	!
70	!
71	! Description:
72	! ------------
73	!> This subroutine reads variables controling the run from the NAMELIST files
74	!>
75	!> @todo: Revise max_pr_cs (profiles for chemistry)
76	!------------------------------------------------------------------------------!
77	SUBROUTINE parin
78
79
80	USE arrays_3d, &
81	ONLY: pt_init, q_init, ref_state, s_init, sa_init, &
82	ug, u_init, v_init, vg
83
84	USE chem_modules
85
86	USE control_parameters
87
88	USE cpulog, &
89	ONLY: cpu_log_barrierwait
90
91	USE date_and_time_mod, &
92	ONLY: date_init, day_of_year_init, time_utc_init
93
94	USE grid_variables, &
95	ONLY: dx, dy
96
97	USE indices, &
98	ONLY: nx, ny, nz
99
100	USE kinds
101
102	USE model_1d_mod, &
103	ONLY: damp_level_1d, dt_pr_1d, dt_run_control_1d, end_time_1d
104
105	USE module_interface, &
106	ONLY: module_interface_parin
107
108	USE netcdf_interface, &
109	ONLY: netcdf_data_format, netcdf_deflate, netcdf_precision
110
111	USE pegrid
112
113	USE pmc_interface, &
114	ONLY: nested_run, nesting_mode
115
116	USE profil_parameter, &
117	ONLY: cross_profiles, profile_columns, profile_rows
118
119	USE progress_bar, &
120	ONLY : progress_bar_disabled
121
122	USE read_restart_data_mod, &
123	ONLY: rrd_global
124
125	USE statistics, &
126	ONLY: hom, hom_sum, pr_palm, statistic_regions
127
128	USE turbulence_closure_mod, &
129	ONLY: rans_const_c, rans_const_sigma
130
131	USE vertical_nesting_mod, &
132	ONLY: vnest_start_time
133
134
135	IMPLICIT NONE
136
137	CHARACTER (LEN=80) :: line !< dummy string that contains the current line of the parameter file
138
139	INTEGER(iwp) :: global_id !< process id with respect to MPI_COMM_WORLD
140	INTEGER(iwp) :: global_procs !< # of procs with respect to MPI_COMM_WORLD
141	INTEGER(iwp) :: i !<
142	INTEGER(iwp) :: ioerr !< error flag for open/read/write
143
144	NAMELIST /inipar/ alpha_surface, approximation, bc_e_b, &
145	bc_lr, bc_ns, bc_p_b, bc_p_t, bc_pt_b, bc_pt_t, bc_q_b, &
146	bc_q_t,bc_s_b, bc_s_t, bc_uv_b, bc_uv_t, &
147	building_height, building_length_x, &
148	building_length_y, building_wall_left, building_wall_south, &
149	calc_soil_moisture_during_spinup, &
150	call_psolver_at_all_substeps, &
151	canyon_height, &
152	canyon_width_x, canyon_width_y, canyon_wall_left, &
153	canyon_wall_south, cfl_factor, cloud_droplets, &
154	collective_wait, complex_terrain, &
155	conserve_volume_flow, &
156	conserve_volume_flow_mode, constant_flux_layer, &
157	coupling_start_time, &
158	cycle_mg, damp_level_1d, &
159	data_output_during_spinup, &
160	date_init, &
161	day_of_year_init, &
162	dissipation_1d, &
163	dp_external, dp_level_b, dp_smooth, dpdxy, &
164	dt, dt_pr_1d, dt_run_control_1d, dt_spinup, dx, dy, dz, dz_max, &
165	dz_stretch_factor, dz_stretch_level, dz_stretch_level_start, &
166	dz_stretch_level_end, end_time_1d, ensemble_member_nr, e_init, &
167	e_min, fft_method, flux_input_mode, flux_output_mode, &
168	galilei_transformation, humidity, &
169	inflow_damping_height, inflow_damping_width, &
170	inflow_disturbance_begin, inflow_disturbance_end, &
171	initializing_actions, km_constant, &
172	large_scale_forcing, large_scale_subsidence, latitude, &
173	longitude, &
174	loop_optimization, lsf_exception, masking_method, mg_cycles, &
175	mg_switch_to_pe0_level, mixing_length_1d, momentum_advec, &
176	monotonic_limiter_z, &
177	netcdf_precision, neutral, ngsrb, &
178	nsor, nsor_ini, nudging, nx, ny, nz, ocean_mode, omega, &
179	omega_sor, outflow_source_plane, passive_scalar, &
180	prandtl_number, psolver, pt_damping_factor, &
181	pt_damping_width, pt_reference, pt_surface, &
182	pt_surface_initial_change, pt_vertical_gradient, &
183	pt_vertical_gradient_level, q_surface, q_surface_initial_change, &
184	q_vertical_gradient, q_vertical_gradient_level, &
185	random_generator, random_heatflux, rans_const_c, rans_const_sigma,&
186	rayleigh_damping_factor, rayleigh_damping_height, &
187	recycling_width, recycling_yshift, &
188	reference_state, residual_limit, &
189	roughness_length, &
190	scalar_advec, &
191	scalar_rayleigh_damping, &
192	spinup_time, spinup_pt_amplitude, spinup_pt_mean, &
193	statistic_regions, subs_vertical_gradient, &
194	subs_vertical_gradient_level, surface_heatflux, surface_pressure, &
195	surface_scalarflux, surface_waterflux, &
196	s_surface, s_surface_initial_change, s_vertical_gradient, &
197	s_vertical_gradient_level, time_utc_init, timestep_scheme, &
198	topography, topography_grid_convention, top_heatflux, &
199	top_momentumflux_u, top_momentumflux_v, &
200	top_scalarflux, transpose_compute_overlap, &
201	tunnel_height, tunnel_length, tunnel_width_x, tunnel_width_y, &
202	tunnel_wall_depth, turbulence_closure, &
203	turbulent_inflow, turbulent_outflow, &
204	use_subsidence_tendencies, ug_surface, ug_vertical_gradient, &
205	use_free_convection_scaling, &
206	ug_vertical_gradient_level, use_surface_fluxes, use_cmax, &
207	use_top_fluxes, use_ug_for_galilei_tr, use_upstream_for_tke, &
208	uv_heights, u_bulk, u_profile, vdi_checks, vg_surface, &
209	vg_vertical_gradient, &
210	vg_vertical_gradient_level, v_bulk, v_profile,&
211	wall_adjustment, wall_heatflux, wall_humidityflux, &
212	wall_scalarflux, y_shift, zeta_max, zeta_min, &
213	z0h_factor
214
215	NAMELIST /initialization_parameters/ alpha_surface, &
216	approximation, bc_e_b, &
217	bc_lr, bc_ns, bc_p_b, bc_p_t, bc_pt_b, bc_pt_t, bc_q_b, &
218	bc_q_t,bc_s_b, bc_s_t, bc_uv_b, bc_uv_t, &
219	building_height, building_length_x, &
220	building_length_y, building_wall_left, building_wall_south, &
221	calc_soil_moisture_during_spinup, &
222	call_psolver_at_all_substeps, &
223	canyon_height, &
224	canyon_width_x, canyon_width_y, canyon_wall_left, &
225	canyon_wall_south, cfl_factor, cloud_droplets, &
226	collective_wait, complex_terrain, &
227	conserve_volume_flow, &
228	conserve_volume_flow_mode, constant_flux_layer, &
229	coupling_start_time, &
230	cycle_mg, damp_level_1d, &
231	data_output_during_spinup, &
232	date_init, &
233	day_of_year_init, &
234	dissipation_1d, &
235	dp_external, dp_level_b, dp_smooth, dpdxy, &
236	dt, dt_pr_1d, dt_run_control_1d, dt_spinup, dx, dy, dz, dz_max, &
237	dz_stretch_factor, dz_stretch_level, dz_stretch_level_start, &
238	dz_stretch_level_end, end_time_1d, ensemble_member_nr, e_init, &
239	e_min, fft_method, flux_input_mode, flux_output_mode, &
240	galilei_transformation, humidity, &
241	inflow_damping_height, inflow_damping_width, &
242	inflow_disturbance_begin, inflow_disturbance_end, &
243	initializing_actions, km_constant, &
244	large_scale_forcing, large_scale_subsidence, latitude, &
245	longitude, &
246	loop_optimization, lsf_exception, masking_method, mg_cycles, &
247	mg_switch_to_pe0_level, mixing_length_1d, momentum_advec, &
248	monotonic_limiter_z, &
249	netcdf_precision, neutral, ngsrb, &
250	nsor, nsor_ini, nudging, nx, ny, nz, ocean_mode, omega, &
251	omega_sor, outflow_source_plane, passive_scalar, &
252	prandtl_number, psolver, pt_damping_factor, &
253	pt_damping_width, pt_reference, pt_surface, &
254	pt_surface_initial_change, pt_vertical_gradient, &
255	pt_vertical_gradient_level, q_surface, q_surface_initial_change, &
256	q_vertical_gradient, q_vertical_gradient_level, &
257	random_generator, random_heatflux, rans_const_c, rans_const_sigma,&
258	rayleigh_damping_factor, rayleigh_damping_height, &
259	recycling_width, recycling_yshift, &
260	recycling_method_for_thermodynamic_quantities, &
261	reference_state, residual_limit, &
262	roughness_length, scalar_advec, &
263	scalar_rayleigh_damping, &
264	spinup_time, spinup_pt_amplitude, spinup_pt_mean, &
265	statistic_regions, subs_vertical_gradient, &
266	subs_vertical_gradient_level, surface_heatflux, surface_pressure, &
267	surface_scalarflux, surface_waterflux, &
268	s_surface, s_surface_initial_change, s_vertical_gradient, &
269	s_vertical_gradient_level, time_utc_init, timestep_scheme, &
270	topography, topography_grid_convention, top_heatflux, &
271	top_momentumflux_u, top_momentumflux_v, &
272	top_scalarflux, transpose_compute_overlap, &
273	tunnel_height, tunnel_length, tunnel_width_x, tunnel_width_y, &
274	tunnel_wall_depth, turbulence_closure, &
275	turbulent_inflow, turbulent_outflow, &
276	use_subsidence_tendencies, ug_surface, ug_vertical_gradient, &
277	ug_vertical_gradient_level, use_surface_fluxes, use_cmax, &
278	use_top_fluxes, use_ug_for_galilei_tr, use_upstream_for_tke, &
279	use_free_convection_scaling, &
280	uv_heights, u_bulk, u_profile, vdi_checks, &
281	vg_surface, vg_vertical_gradient, &
282	vg_vertical_gradient_level, v_bulk, v_profile, &
283	wall_adjustment, wall_heatflux, wall_humidityflux, &
284	wall_scalarflux, y_shift, zeta_max, zeta_min, z0h_factor
285
286	NAMELIST /d3par/ averaging_interval, averaging_interval_pr, &
287	cpu_log_barrierwait, create_disturbances, &
288	cross_profiles, data_output, data_output_masks, &
289	data_output_pr, data_output_2d_on_each_pe, &
290	debug_output, &
291	debug_output_timestep, &
292	disturbance_amplitude, &
293	disturbance_energy_limit, disturbance_level_b, &
294	disturbance_level_t, do2d_at_begin, do3d_at_begin, &
295	dt, dt_averaging_input, dt_averaging_input_pr, &
296	dt_coupling, dt_data_output, dt_data_output_av, dt_disturb, &
297	dt_domask, dt_dopr, dt_dopr_listing, dt_dots, dt_do2d_xy, &
298	dt_do2d_xz, dt_do2d_yz, dt_do3d, dt_max, dt_restart, &
299	dt_run_control,end_time, force_print_header, mask_k_over_surface, &
300	mask_scale_x, &
301	mask_scale_y, mask_scale_z, mask_x, mask_y, mask_z, mask_x_loop, &
302	mask_y_loop, mask_z_loop, netcdf_data_format, netcdf_deflate, &
303	normalizing_region, npex, npey, nz_do3d, &
304	profile_columns, profile_rows, &
305	restart_time, section_xy, section_xz, section_yz, &
306	skip_time_data_output, skip_time_data_output_av, skip_time_dopr, &
307	skip_time_do2d_xy, skip_time_do2d_xz, skip_time_do2d_yz, &
308	skip_time_do3d, skip_time_domask, synchronous_exchange, &
309	termination_time_needed, vnest_start_time
310
311	NAMELIST /runtime_parameters/ averaging_interval, averaging_interval_pr, &
312	cpu_log_barrierwait, create_disturbances, &
313	cross_profiles, data_output, data_output_masks, &
314	data_output_pr, data_output_2d_on_each_pe, &
315	debug_output, &
316	debug_output_timestep, &
317	disturbance_amplitude, &
318	disturbance_energy_limit, disturbance_level_b, &
319	disturbance_level_t, do2d_at_begin, do3d_at_begin, &
320	dt, dt_averaging_input, dt_averaging_input_pr, &
321	dt_coupling, dt_data_output, dt_data_output_av, dt_disturb, &
322	dt_domask, dt_dopr, dt_dopr_listing, dt_dots, dt_do2d_xy, &
323	dt_do2d_xz, dt_do2d_yz, dt_do3d, dt_max, dt_restart, &
324	dt_run_control,end_time, force_print_header, mask_k_over_surface, &
325	mask_scale_x, &
326	mask_scale_y, mask_scale_z, mask_x, mask_y, mask_z, mask_x_loop, &
327	mask_y_loop, mask_z_loop, netcdf_data_format, netcdf_deflate, &
328	normalizing_region, npex, npey, nz_do3d, &
329	profile_columns, profile_rows, &
330	restart_time, section_xy, section_xz, section_yz, &
331	skip_time_data_output, skip_time_data_output_av, skip_time_dopr, &
332	skip_time_do2d_xy, skip_time_do2d_xz, skip_time_do2d_yz, &
333	skip_time_do3d, skip_time_domask, synchronous_exchange, &
334	termination_time_needed, vnest_start_time
335
336	NAMELIST /envpar/ progress_bar_disabled, host, &
337	maximum_cpu_time_allowed, maximum_parallel_io_streams, &
338	read_svf, revision, run_identifier, tasks_per_node, &
339	write_binary, write_svf
340
341	!
342	!-- First read values of environment variables (this NAMELIST file is
343	!-- generated by palmrun)
344	CALL location_message( 'reading environment parameters from ENVPAR', 'start' )
345
346	OPEN ( 90, FILE='ENVPAR', STATUS='OLD', FORM='FORMATTED', IOSTAT=ioerr )
347
348	IF ( ioerr /= 0 ) THEN
349	message_string = 'local file ENVPAR not found' // &
350	'&some variables for steering may not be properly set'
351	CALL message( 'parin', 'PA0276', 0, 1, 0, 6, 0 )
352	ELSE
353	READ ( 90, envpar, IOSTAT=ioerr )
354	IF ( ioerr < 0 ) THEN
355	message_string = 'no envpar-NAMELIST found in local file ' // &
356	'ENVPAR& or some variables for steering may ' // &
357	'not be properly set'
358	CALL message( 'parin', 'PA0278', 0, 1, 0, 6, 0 )
359	ELSEIF ( ioerr > 0 ) THEN
360	message_string = 'errors in local file ENVPAR' // &
361	'&some variables for steering may not be properly set'
362	CALL message( 'parin', 'PA0277', 0, 1, 0, 6, 0 )
363	ENDIF
364	CLOSE ( 90 )
365	ENDIF
366
367	CALL location_message( 'reading environment parameters from ENVPAR', 'finished' )
368	!
369	!-- Calculate the number of groups into which parallel I/O is split.
370	!-- The default for files which are opened by all PEs (or where each
371	!-- PE opens his own independent file) is, that all PEs are doing input/output
372	!-- in parallel at the same time. This might cause performance or even more
373	!-- severe problems depending on the configuration of the underlying file
374	!-- system.
375	!-- Calculation of the number of blocks and the I/O group must be based on all
376	!-- PEs involved in this run. Since myid and numprocs are related to the
377	!-- comm2d communicator, which gives only a subset of all PEs in case of
378	!-- nested runs, that information must be inquired again from the global
379	!-- communicator.
380	!-- First, set the default:
381	#if defined( __parallel )
382	CALL MPI_COMM_RANK( MPI_COMM_WORLD, global_id, ierr )
383	CALL MPI_COMM_SIZE( MPI_COMM_WORLD, global_procs, ierr )
384	#else
385	global_id = 0
386	global_procs = 1
387	#endif
388	IF ( maximum_parallel_io_streams == -1 .OR. &
389	maximum_parallel_io_streams > global_procs ) THEN
390	maximum_parallel_io_streams = global_procs
391	ENDIF
392	!
393	!-- Now calculate the number of io_blocks and the io_group to which the
394	!-- respective PE belongs. I/O of the groups is done in serial, but in parallel
395	!-- for all PEs belonging to the same group.
396	io_blocks = global_procs / maximum_parallel_io_streams
397	io_group = MOD( global_id+1, io_blocks )
398
399	CALL location_message( 'reading NAMELIST parameters from PARIN', 'start' )
400	!
401	!-- Data is read in parallel by groups of PEs
402	DO i = 0, io_blocks-1
403	IF ( i == io_group ) THEN
404
405	!
406	!-- Open the NAMELIST-file which is send with this job
407	CALL check_open( 11 )
408
409	!
410	!-- Read the control parameters for initialization.
411	!-- The namelist "inipar" must be provided in the NAMELIST-file.
412	READ ( 11, initialization_parameters, ERR=10, END=11 )
413	GOTO 14
414
415	10 BACKSPACE( 11 )
416	READ( 11 , '(A)') line
417	CALL parin_fail_message( 'initialization_parameters', line )
418
419	11 REWIND ( 11 )
420	READ ( 11, inipar, ERR=12, END=13 )
421
422	message_string = 'namelist inipar is deprecated and will be ' // &
423	'removed in near future. & Please use namelist ' // &
424	'initialization_parameters instead'
425	CALL message( 'parin', 'PA0017', 0, 1, 0, 6, 0 )
426
427	GOTO 14
428
429	12 BACKSPACE( 11 )
430	READ( 11 , '(A)') line
431	CALL parin_fail_message( 'inipar', line )
432
433	13 message_string = 'no initialization_parameters-namelist found'
434	CALL message( 'parin', 'PA0272', 1, 2, 0, 6, 0 )
435
436	!
437	!-- Try to read runtime parameters given by the user for this run
438	!-- (namelist "runtime_parameters"). The namelist "runtime_parmeters"
439	!-- can be omitted. In that case default values are used for the
440	!-- parameters.
441	14 line = ' '
442
443	REWIND ( 11 )
444	line = ' '
445	DO WHILE ( INDEX( line, '&runtime_parameters' ) == 0 )
446	READ ( 11, '(A)', END=16 ) line
447	ENDDO
448	BACKSPACE ( 11 )
449
450	!
451	!-- Read namelist
452	READ ( 11, runtime_parameters, ERR = 15 )
453	GOTO 18
454
455	15 BACKSPACE( 11 )
456	READ( 11 , '(A)') line
457	CALL parin_fail_message( 'runtime_parameters', line )
458
459	16 REWIND ( 11 )
460	line = ' '
461	DO WHILE ( INDEX( line, '&d3par' ) == 0 )
462	READ ( 11, '(A)', END=18 ) line
463	ENDDO
464	BACKSPACE ( 11 )
465
466	!
467	!-- Read namelist
468	READ ( 11, d3par, ERR = 17, END = 18 )
469
470	message_string = 'namelist d3par is deprecated and will be ' // &
471	'removed in near future. &Please use namelist ' // &
472	'runtime_parameters instead'
473	CALL message( 'parin', 'PA0487', 0, 1, 0, 6, 0 )
474
475	GOTO 18
476
477	17 BACKSPACE( 11 )
478	READ( 11 , '(A)') line
479	CALL parin_fail_message( 'd3par', line )
480
481	18 CONTINUE
482
483	!
484	!-- Check for module namelists and read them
485	CALL module_interface_parin
486
487	!
488	!-- If required, read control parameters from restart file (produced by
489	!-- a prior run). All PEs are reading from file created by PE0 (see
490	!-- check_open)
491	IF ( TRIM( initializing_actions ) == 'read_restart_data' ) THEN
492
493	CALL rrd_global
494	!
495	!-- Increment the run count
496	runnr = runnr + 1
497	!
498	!-- In case of a restart run, the number of user-defined profiles on
499	!-- the restart file (already stored in max_pr_user) has to match the
500	!-- one given for the current run. max_pr_user_tmp is calculated in
501	!-- user_parin and max_pr_user is read in via rrd_global.
502	IF ( max_pr_user /= max_pr_user_tmp ) THEN
503	WRITE( message_string, * ) 'the number of user-defined ', &
504	'profiles given in data_output_pr (', max_pr_user_tmp, &
505	') does not match the one ', &
506	'found in the restart file (', max_pr_user, ')'
507	CALL message( 'user_parin', 'UI0009', 1, 2, 0, 6, 0 )
508	ENDIF
509	ELSE
510	max_pr_user = max_pr_user_tmp
511	ENDIF
512	!
513	!-- Activate spinup
514	IF ( land_surface .OR. urban_surface ) THEN
515	IF ( spinup_time > 0.0_wp ) THEN
516	coupling_start_time = spinup_time
517	time_since_reference_point = simulated_time - coupling_start_time
518	IF ( spinup_pt_mean == 9999999.9_wp ) THEN
519	spinup_pt_mean = pt_surface
520	ENDIF
521	end_time = end_time + spinup_time
522	IF ( TRIM( initializing_actions ) /= 'read_restart_data' ) THEN
523	spinup = .TRUE.
524	ELSEIF ( TRIM( initializing_actions ) == 'read_restart_data' &
525	.AND. time_since_reference_point > 0.0_wp ) THEN
526	data_output_during_spinup = .FALSE. !< required for correct ntdim calculation
527	!< in check_parameters for restart run
528	ENDIF
529	ENDIF
530	ENDIF
531
532	!
533	!-- In case of nested runs, explicitly set nesting boundary conditions.
534	!-- This will overwrite the user settings and basic defaults.
535	!-- bc_lr and bc_ns always need to be cyclic for vertical nesting.
536	IF ( nested_run ) THEN
537	IF ( nesting_mode == 'vertical' ) THEN
538	IF (bc_lr /= 'cyclic' .OR. bc_ns /= 'cyclic' ) THEN
539	WRITE ( message_string, *) 'bc_lr and bc_ns were set to ,', &
540	'cyclic for vertical nesting'
541	CALL message( 'parin', 'PA0428', 0, 0, 0, 6, 0 )
542	bc_lr = 'cyclic'
543	bc_ns = 'cyclic'
544	ENDIF
545	IF ( child_domain ) THEN
546	bc_uv_t = 'nested'
547	bc_pt_t = 'nested'
548	bc_q_t = 'nested'
549	bc_s_t = 'nested'
550	bc_cs_t = 'nested'
551	bc_p_t = 'neumann'
552	ENDIF
553	!
554	!-- For other nesting modes only set boundary conditions for
555	!-- nested domains.
556	ELSE
557	IF ( child_domain ) THEN
558	bc_lr = 'nested'
559	bc_ns = 'nested'
560	bc_uv_t = 'nested'
561	bc_pt_t = 'nested'
562	bc_q_t = 'nested'
563	bc_s_t = 'nested'
564	bc_cs_t = 'nested'
565	bc_p_t = 'neumann'
566	ENDIF
567	ENDIF
568	ENDIF
569	!
570	!-- Set boundary conditions also in case the model is offline-nested in
571	!-- larger-scale models.
572	IF ( nesting_offline ) THEN
573	bc_lr = 'nesting_offline'
574	bc_ns = 'nesting_offline'
575	bc_uv_t = 'nesting_offline'
576	bc_pt_t = 'nesting_offline'
577	bc_q_t = 'nesting_offline'
578	! bc_s_t = 'nesting_offline' ! scalar boundary condition is not clear yet
579	! bc_cs_t = 'nesting_offline' ! same for chemical species
580	bc_p_t = 'neumann'
581	ENDIF
582
583	!
584	!-- In case of nested runs, make sure that initializing_actions =
585	!-- 'set_constant_profiles' even though the constant-profiles
586	!-- initializations for the prognostic variables will be overwritten
587	!-- by pmci_child_initialize and pmci_parent_initialize. This is,
588	!-- however, important e.g. to make sure that diagnostic variables
589	!-- are set properly. An exception is made in case of restart runs and
590	!-- if user decides to do everything by its own.
591	IF ( child_domain .AND. .NOT. ( &
592	TRIM( initializing_actions ) == 'read_restart_data' .OR. &
593	TRIM( initializing_actions ) == 'set_constant_profiles' .OR. &
594	TRIM( initializing_actions ) == 'by_user' ) ) THEN
595	message_string = 'initializing_actions = ' // &
596	TRIM( initializing_actions ) // ' has been ' // &
597	'changed to set_constant_profiles in child ' // &
598	'domain.'
599	CALL message( 'parin', 'PA0492', 0, 0, 0, 6, 0 )
600
601	initializing_actions = 'set_constant_profiles'
602	ENDIF
603	!
604	!-- Check validity of lateral boundary conditions. This has to be done
605	!-- here because they are already used in init_pegrid and init_grid and
606	!-- therefore cannot be check in check_parameters
607	IF ( bc_lr /= 'cyclic' .AND. bc_lr /= 'dirichlet/radiation' .AND. &
608	bc_lr /= 'radiation/dirichlet' .AND. bc_lr /= 'nested' .AND. &
609	bc_lr /= 'nesting_offline' ) THEN
610	message_string = 'unknown boundary condition: bc_lr = "' // &
611	TRIM( bc_lr ) // '"'
612	CALL message( 'parin', 'PA0049', 1, 2, 0, 6, 0 )
613	ENDIF
614	IF ( bc_ns /= 'cyclic' .AND. bc_ns /= 'dirichlet/radiation' .AND. &
615	bc_ns /= 'radiation/dirichlet' .AND. bc_ns /= 'nested' .AND. &
616	bc_ns /= 'nesting_offline' ) THEN
617	message_string = 'unknown boundary condition: bc_ns = "' // &
618	TRIM( bc_ns ) // '"'
619	CALL message( 'parin', 'PA0050', 1, 2, 0, 6, 0 )
620	ENDIF
621	!
622	!-- Set internal variables used for speed optimization in if clauses
623	IF ( bc_lr /= 'cyclic' ) bc_lr_cyc = .FALSE.
624	IF ( bc_lr == 'dirichlet/radiation' ) bc_lr_dirrad = .TRUE.
625	IF ( bc_lr == 'radiation/dirichlet' ) bc_lr_raddir = .TRUE.
626	IF ( bc_ns /= 'cyclic' ) bc_ns_cyc = .FALSE.
627	IF ( bc_ns == 'dirichlet/radiation' ) bc_ns_dirrad = .TRUE.
628	IF ( bc_ns == 'radiation/dirichlet' ) bc_ns_raddir = .TRUE.
629	!
630	!-- Radiation-Dirichlet conditions are allowed along one of the horizontal directions only.
631	!-- In general, such conditions along x and y may work, but require a) some code changes
632	!-- (e.g. concerning allocation of c_u, c_v ... arrays), and b) a careful model setup by the
633	!-- user, in order to guarantee that there is a clearly defined outflow at two sides.
634	!-- Otherwise, the radiation condition may produce wrong results.
635	IF ( ( bc_lr_dirrad .OR. bc_lr_raddir ) .AND. ( bc_ns_dirrad .OR. bc_ns_raddir ) ) THEN
636	message_string = 'bc_lr = "' // TRIM( bc_lr ) // '" and bc_ns = "' // &
637	TRIM( bc_ns ) // '" are not allowed to be set at the same time'
638	CALL message( 'parin', 'PA0589', 1, 2, 0, 6, 0 )
639	ENDIF
640	!
641	!-- Check in case of initial run, if the grid point numbers are well
642	!-- defined and allocate some arrays which are already needed in
643	!-- init_pegrid or check_parameters. During restart jobs, these arrays
644	!-- will be allocated in rrd_global. All other arrays are allocated
645	!-- in init_3d_model.
646	IF ( TRIM( initializing_actions ) /= 'read_restart_data' ) THEN
647
648	IF ( nx <= 0 ) THEN
649	WRITE( message_string, * ) 'no value or wrong value given', &
650	' for nx: nx=', nx
651	CALL message( 'parin', 'PA0273', 1, 2, 0, 6, 0 )
652	ENDIF
653	IF ( ny <= 0 ) THEN
654	WRITE( message_string, * ) 'no value or wrong value given', &
655	' for ny: ny=', ny
656	CALL message( 'parin', 'PA0274', 1, 2, 0, 6, 0 )
657	ENDIF
658	IF ( nz <= 0 ) THEN
659	WRITE( message_string, * ) 'no value or wrong value given', &
660	' for nz: nz=', nz
661	CALL message( 'parin', 'PA0275', 1, 2, 0, 6, 0 )
662	ENDIF
663
664	!
665	!-- As a side condition, routine flow_statistics require at least 14
666	!-- vertical grid levels (they are used to store time-series data)
667	!> @todo Remove this restriction
668	IF ( nz < 14 ) THEN
669	WRITE( message_string, * ) 'nz >= 14 is required'
670	CALL message( 'parin', 'PA0362', 1, 2, 0, 6, 0 )
671	ENDIF
672
673	!
674	!-- ATTENTION: in case of changes to the following statement please
675	!-- also check the allocate statement in routine rrd_global
676	ALLOCATE( pt_init(0:nz+1), q_init(0:nz+1), s_init(0:nz+1), &
677	ref_state(0:nz+1), sa_init(0:nz+1), ug(0:nz+1), &
678	u_init(0:nz+1), v_init(0:nz+1), vg(0:nz+1), &
679	hom(0:nz+1,2,pr_palm+max_pr_user+max_pr_cs+max_pr_salsa,0:statistic_regions), &
680	hom_sum(0:nz+1,pr_palm+max_pr_user+max_pr_cs+max_pr_salsa,0:statistic_regions) )
681
682	hom = 0.0_wp
683
684	ENDIF
685
686	!
687	!-- NAMELIST-file is not needed anymore
688	CALL close_file( 11 )
689
690	ENDIF
691	#if defined( __parallel )
692	CALL MPI_BARRIER( MPI_COMM_WORLD, ierr )
693	#endif
694	ENDDO
695
696	CALL location_message( 'reading NAMELIST parameters from PARIN', 'finished' )
697
698	END SUBROUTINE parin

Note: See TracBrowser for help on using the repository browser.

Download in other formats:

| Impressum | ©Leibniz Universität Hannover |