Changes between Version 96 and Version 97 of doc/app/runtime_parameters

Timestamp:

Sep 14, 2010 2:55:54 PM (15 years ago)

Author:

weinreis

Comment:

--

doc/app/runtime_parameters

@@ -457 +457 @@
 |----------------
 {{{#!td style="vertical-align:top"
+[=#dt_do2d_xz '''dt_do2d_xz''']
+}}}
+{{{#!td style="vertical-align:top"
+R
+}}}
+{{{#!td style="vertical-align:top"
+value of\\ [#dt_data_output dt_data]\\[#dt_data_output _output]
+}}}
+{{{#!td
+Temporal interval at which vertical cross sections data (xz) shall be output (in s).\\\\
+If output of horizontal cross sections is switched on (see [#data_output data_output] and [#section_xz section_xz]), this parameter can be used to assign the temporal interval at which cross section data shall be output. Output can be skipped at the beginning of a simulation using parameter [#skip_time_do2d_xz skip_time_do2d_xz], which has zero value by default. Reference time is the beginning of the simulation, i.e. output takes place at times t = '''skip_time_do2d_xz''' + '''dt_do2d_xz''', '''skip_time_do2d_xz''' + 2*'''dt_do2d_xz''', '''skip_time_do2d_xz''' + 3*'''dt_do2d_xz''', etc. The actual output times can deviate from these theoretical values (see [#dt_dopr dt_dopr]).\\\\
+Parameter [#do2d_at_begin do2d_at_begin] has to be used if an additional output is wanted at the start of a run (thus at the time t = 0 or at the respective starting times of restart runs). 
+}}}
+|----------------
+{{{#!td style="vertical-align:top"
+[=#dt_do2d_yz '''dt_do2d_yz''']
+}}}
+{{{#!td style="vertical-align:top"
+R
+}}}
+{{{#!td style="vertical-align:top"
+value of\\ [#dt_data_output dt_data]\\[#dt_data_output _output]
+}}}
+{{{#!td
+Temporal interval at which vertical cross section data (yz) shall be output (in s).\\\\
+If output of horizontal cross sections is switched on (see [#data_output data_output] and [#section_yz section_yz]), this parameter can be used to assign the temporal interval at which cross section data shall be output. Output can be skipped at the beginning of a simulation using parameter [#skip_time_do2d_yz skip_time_do2d_yz], which has zero value by default. Reference time is the beginning of the simulation, i.e. output takes place at times t = '''skip_time_do2d_yz''' + '''dt_do2d_yz''', '''skip_time_do2d_yz''' + 2*'''dt_do2d_yz''', '''skip_time_do2d_yz''' + 3*'''dt_do2d_yz''', etc. The actual output times can deviate from these theoretical values (see [#dt_dopr dt_dopr]).\\\\
+Parameter [#do2d_at_begin do2d_at_begin] has to be used if an additional output is wanted at the start of a run (thus at the time t = 0 or at the respective starting times of restart runs).
+}}}
+|----------------
+{{{#!td style="vertical-align:top"
+[=#dt_do3d '''dt_do3d''']
+}}}
+{{{#!td style="vertical-align:top"
+R
+}}}
+{{{#!td style="vertical-align:top"
+value of\\ [#dt_data_output dt_data]\\[#dt_data_output _output]
+}}}
+{{{#!td
+Temporal interval at which 3d volume data shall be output (in s).\\\\
+If output of 3d-volume data is switched on (see [#data_output data_output]), this parameter can be used to assign the temporal interval at which 3d-data shall be output. Output can be skipped at the beginning of a simulation using parameter [#skip_time_do3d skip_time_do3d], which has zero value by default. Reference time is the beginning of the simulation, i.e. output takes place at times t = '''skip_time_do3d''' + '''dt_do3d''', '''skip_time_do3d''' + 2*'''dt_do3d''', '''skip_time_do3d''' + 3*'''dt_do3d''', etc. The actual output times can deviate from these theoretical values (see [#dt_dopr dt_dopr]).\\\\
+Parameter [#do3d_at_begin do3d_at_begin] has to be used if an additional output is wanted at the start of a run (thus at the time t = 0 or at the respective starting times of restart runs).
+}}}
+|----------------
+{{{#!td style="vertical-align:top"
 [=#dummy '''dummy''']
 }}}