Changes between Version 230 and Version 231 of doc/app/parlist

Timestamp:

Nov 5, 2018 2:08:52 PM (7 years ago)

Author:

weniger

Comment:

--

doc/app/parlist

@@ -299 +299 @@
 || [../d3par#npex npex] || run || I || no default value || Number of processors along x-direction of the virtual processor net. 
 || [../d3par#npey npey] || run || I || no default value || Number of processors along y-direction of the virtual processor net. 
+|| [../salsa#nsnucl nsnucl] || salsa || I ||0|| The nucleation scheme applied. 
 || [../inipar#nsor nsor] || run || I ||20|| Number of iterations to be used with the SOR-scheme. 
 || [../inipar#nsor_ini nsor_ini] || ini || I ||100|| Initial number of iterations with the SOR algorithm. 
@@ -310 +311 @@
 || [../inipar#nz nz] || ini || I || no default value || Number of grid points in z-direction. 
 || [../d3par#nz_do3d nz_do3d] || ini || I || nz + 1 || Limits the output of 3d volume data along the vertical direction (grid point index k). 
-|| [../inipar#omega omega] || ini || R ||7,29E+00|| Angular velocity of the rotating system (in rad s^-1^). 
+|| [../salsa#OCNV_init OCNV_init] [=#o] || salsa || R ||1.0|| Initial number concentration (in m^-3^) of gaseous non-volatile organic compounds. 
+|| [../salsa#OCSV_init OCSV_init] || salsa || R ||1.0|| Initial number concentration (in m^-3^) of gaseous semi-volatile organic compounds. 
+|| [../inipar#omega omega] || ini || R ||7.29E+00|| Angular velocity of the rotating system (in rad s^-1^). 
 || [../wind_turbine_par#omega_rot omega_rot] || wtm || R(100) || 0.0 || Initial rotational speed for each turbine (in rad s^-1^). 
 || [../inipar#omega_sor omega_sor] || ini || R || 1.8 || Convergence factor to be used with the SOR-scheme. 
@@ -354 +357 @@
 || [../inipar#q_vertical_gradient q_vertical_gradient] || ini || R(10) || 10*0.0 || Humidity gradient(s) of the initial humidity profile (in 1/100 m). 
 || [../inipar#q_vertical_gradient_level q_vertical_gradient] \\ [../inipar#q_vertical_gradient_level _level] || ini || R(10) || 10*0.0 || Height level above which the humidity gradient defined by [../inipar#q_vertical_gradient q_vertical_gradient] is effective (in m). 
-|| [../parpar#rm rm][=#r] || lpm || R(3) || 0.05E-6 || Parameters of initial aerosol spectrum. 
-|| [../inipar#radiation radiation] || ini || L || .F. || Parameter to switch on longwave radiation cooling at cloud-tops. 
+|| [../inipar#radiation radiation][=#r]  || ini || L || .F. || Parameter to switch on longwave radiation cooling at cloud-tops. 
 || [../radpar#radiation_scheme radiation_scheme] || rrtmg || C*10 || 'clear-sky' || Radiation scheme to be used. 
 || [../parpar#radius radius] || lpm || R(10) || 0.0, 9* \\ 9999999.9 || Particle radius (in m). 
@@ -370 +372 @@
 || [../wind_turbine_par#rcz rcz] || wtm || R(100) || none || Vertical position of the rotor center (in m). This represents the hub height of the turbine. 
 || [../parpar#read_particles_from_restartfile read_particles_from] \\ [../parpar#read_particles_from_restartfile _restartfile] || lpm || L || .T. || Read particle data from the previous run. 
+|| [../salsa#read_restart_data_salsa read_restart_data_salsa]  || salsa || L || .F. || Read the restart data of the salsa module from the previous run. 
 || [../inipar#recycling_width recycling_width] || ini || R || 0.1*[../inipar#nx nx]*[../inipar#dx dx] || Distance of the recycling plane from the inflow boundary (in m). 
 || [../inipar#recycling_yshift recycling_yshift] || ini || L || .F. || Parameter to switch on a y-shift for the recycled inflow turbulence. 
 || [../inipar#reference_state reference_state] || ini || C*20 || '' 'initial_profile' '' || Defines what is used as reference state in the buoyancy term. 
 || [../userpar#region region] || user || C*40(0:9) |||| Name(s) of the subdomain(s) defined by the user. 
+|| [../salsa#reglim reglim]  || salsa || R(3) || 3.0E-9, 5.0E-8, 1.0E-5  || Aerosol diameter limits for the subranges (in m) in the following order: lower limit of 1, upper limit of 1 and lower limit of 2, upper limit of 2. 
 || [../inipar#residual_limit residual_limit] || ini || R || 1.0E-6 || Largest residual permitted for the multigrid scheme (in s^-2^m^-3^). 
 || [../lsmpar#residual_moisture residual_moisture] || lsm || R || depends on [../lsmpar#soil_type soil_type] || Residual soil moisture content (in m³/m³). 
 || [../d3par#restart_time restart_time] || run || R || 9999999.9 || Simulated time after which a restart run is to be carried out (in s). 
+|| [../parpar#rm rm]|| lpm || R(3) || 0.05E-6 || Parameters of initial aerosol spectrum. 
 || [../wind_turbine_par#rnac rnac] || wtm || R(100) || none || Radius of the nacelle for each turbine (in m). This parameter has to be non-zero if the nacelle should be included. 
 || [../lsmpar#root_fraction root_fraction] || lsm || R(4) || depends on [../lsmpar#veg_type veg_type] || Root distribution over the four soil layers. 
@@ -386 +391 @@
 || [../inipar#s_vertical_gradient_level s_vertical_gradient] \\ [../inipar#s_vertical_gradient_level _level] || ini || R(10) || 10*0.0 || Height level above which the scalar gradient defined by [../inipar#s_vertical_gradient s_vertical_gradient] is effective (in m). 
 || [../oceanpar#salinity salinity] || ocean || L || .T. || Parameter to switch on/off calculation of salinity equation. 
+|| [../salsa#salsa_source_mode salsa_source_mode] || salsa || C(20) || 'no_source'  || Source mode for aerosol and gaseous emissions. 
 || [../oceanpar#sa_surface sa_surface] || ocean || R || 35.0 || Surface salinity (in psu). 
 || [../oceanpar#sa_vertical_gradient sa_vertical_gradient] || ocean || R(10) || 10*0.0 || Salinity gradient(s) of the initial salinity profile (in psu / 100 m). 
@@ -399 +405 @@
 || [../wind_turbine_par#segment_width segment_width] || wtm || R || 0.5 || Length of each rotor segment the rotor area is divided into, in radial direction, as factor of the grid spacing. 
 || [../inipar#sigma_bulk sigma_bulk] || ini || R || 2.0 || The dispersion of the dry aerosol spectrum. 
+|| [../salsa#sigmag sigmag] || salsa || R(7) || 1.8, 2.16, 2.21, 2.0, 2.0, 2.0, 2.0   || The standard deviation of the log-normal aerosol number size distribution per aerosol mode.
 || [../d3par#skip_time_data_output skip_time_data_output] || run || R || 0.0 || No data output before this interval has passed (in s). 
 || [../d3par#skip_time_data_output_av skip_time_data] \\ [../d3par#skip_time_data_output_av _output_av] || run || R || value of [../d3par#skip_time_data_output skip_time] \\ [../d3par#skip_time_data_output _data_output] || No output of temporally averaged 2d/3d data before this interval has passed (in s). 
 || [../lsmpar#skip_time_do_lsm skip_time_do_lsm] || lsm || R || 0.0 || Time after which the land surface model is switched on. 
 || [../radpar#skip_time_do_radiation skip_time_do_radiation] || rrtmg || R || 0.0 || Time after which the radiation model is switched on. 
+|| [../salsa#skip_time_do_salsa skip_time_do_salsa] || salsa || R || 0.0 || Time after which SALSA is switched on. 
 || [../d3par#skip_time_domask skip_time_domask] || run || R \\ (max_masks) || max_masks*0.0 || No output of masked data before this interval has passed (in s). 
 || [../d3par#skip_time_dopr skip_time_dopr] || run || R || value of [../d3par#skip_time_data_output skip_time] \\ [../d3par#skip_time_data_output _data_output] || No output of vertical profile data before this interval has passed (in s). 
@@ -471 +479 @@
 || [../inipar#use_ug_for_galilei_tr use_ug_for_galilei_tr] || ini || L || .T. || Switch to determine the translation velocity in case that a Galilean transformation is used. 
 || [../inipar#use_upstream_for_tke use_upstream] \\ [../inipar#use_upstream_for_tke _for_tke] || ini || L || .F. || Parameter to choose the advection/timestep scheme to be used for the subgrid-scale TKE. 
-|| [../parpar#vertical_particle_advection vertical_particle] [=#v] \\ [../parpar#vertical_particle_advection _advection] || lpm || L || .T. || Switch on/off vertical particle transport. 
-|| [../inipar#v_bulk v_bulk] || ini || R || 0.0 || v-component of the predefined bulk velocity (in m/s). 
+|| [../inipar#v_bulk v_bulk] [=#v] || ini || R || 0.0 || v-component of the predefined bulk velocity (in m/s). 
 || [../inipar#v_profile v_profile] || ini || R(100) || 100 * 9999999.9 || Values of v-velocity component to be used as initial profile (in m/s). 
 || [../lsmpar#veg_type veg_type] || lsm || I ||2|| Vegetation type to be used in the land surface model. 
 || [../lsmpar#vegetation_coverage vegetation_coverage] || lsm || R || depends on [../lsmpar#veg_type veg_type] || Vegetation coverage of the surface. 
 || [../inipar#ventilation_effect ventilation_effect] || ini || L || .T. || Parameterize ventilation effect on evaporation of raindrops. 
+|| [../parpar#vertical_particle_advection vertical_particle] \\ [../parpar#vertical_particle_advection _advection] || lpm || L || .T. || Switch on/off vertical particle transport.
 || [../inipar#vg_surface vg_surface] || ini || R || 0.0 || v-component of the geostrophic wind at the surface (in m/s). 
 || [../inipar#vg_vertical_gradient vg_vertical_gradient] || ini || R(10) || 10*0.0 || Gradient(s) of the initial profile of thev-component of the geostrophic wind (in 1/100s).