PALM error messages

Explanation
In the following list the error messages reported by PALM are mentioned. Each error message is identified unambiguously by a message identifier which is composed of two letters and a number. The second column contains the error message which is reported in the job protocol (see 3.1?). In addition, the third column includes further explanations of the error.

PA****	Identifier for messages in the PALM standard code
UI****	Identifier for messages in ''user_'' routines
NC****	Identifier for messages from the netCDF library

Message identifier	Error message	Explanation
PA0001	"host" is not set. Please check that environment variable "localhost" is set before running PALM
PA0002	illegal coupling mode: ...
PA0003	dt_coupling is not set but required for coupling mode "..."
PA0004	coupling mode "...": dt_coupling = ... is not equal to dt_coupling_remote = ...
PA0005	coupling mode "...": dt_coupling <= 0.0 is not allowed and is reset to MAX(dt_max(A,O)) = ...
PA0006	coupling mode "...": restart_time = ... is not equal to restart_time_remote = ...
PA0007	coupling mode "...": dt_restart = ... is not equal to dt_restart_remote = ...
PA0008	coupling mode "...": simulation_time_since_reference = ... is not equal to simulation_time_since_reference_remote = ...
PA0009	coupling mode "...": dx = ... is not equal to dx_remote = ...
PA0010	coupling mode "...": dy = ... is not equal to dy_remote = ...
PA0011	coupling mode "...": nx = ... is not equal to nx_remote = ...
PA0012	coupling mode "...": ny = ... is not equal to ny_remote = ...
PA0013	illegal value given for loop_optimization: "..."
PA0014	a non-flat topography does not allow ...
PA0015	ocean = .T. does not allow ...
PA0016	unknown solver for perturbation pressure: psolver = "..."
PA0017	psolver = "..." only works for a 1d domain-decomposition along x please do not set npey/=1 in the parameter file
PA0018	psolver = ".." does not work for subdomains with unequal size please set grid_matching = strict in the parameter file
PA0019	psolver = "..." only works for a parallel environment
PA0020	unknown multigrid cycle: cycle_mg = "..."
PA0021	unknown fft-algorithm: fft_method = "..."
PA0022	unknown advection scheme: momentum_advec = "..."
PA0023	momentum_advec = "..." is not allowed with timestep_scheme = "..."
PA0024	unknown advection scheme: scalar_advec = "..."
PA0025	use_upstream_for_tke set .TRUE. because use_sgs_for_particles = .TRUE.
PA0026	use_upstream_for_tke = .TRUE. not allowed with timestep_scheme = "..."
PA0027	unknown timestep scheme: timestep_scheme = "..."
PA0028	scalar advection scheme "..." does not work with timestep_scheme "..."
PA0029	momentum advection scheme "..." does not work with timestep_scheme "..."
PA0030	initializing_action = "..." unkown or not allowed
PA0031	initializing_actions = "set_constant_profiles" and "set_1d-model_profiles" are not allowed simultaneously
PA0032	initializing_actions = "set_constant_profiles" and "by_user" are not allowed simultaneously
PA0033	initializing_actions = "by_user" and "set_1d-model_profiles" are not allowed simultaneously
PA0034	cloud_physics = ... is not allowed with humidity = ...
PA0035	precipitation = ... is not allowed with cloud_physics = ...
PA0036	humidity = .TRUE. and sloping_surface = .TRUE. are not allowed simultaneously
PA0037	UPS-scheme is not implemented for humidity = .TRUE.
PA0038	humidity = .TRUE. and passive_scalar = .TRUE. is not allowed simultaneously'
PA0039	UPS-scheme is not implemented for passive_scalar = .TRUE.
PA0040	illegal value "..." found for parameter grid_matching
PA0041	plant_canopy = .TRUE. requires a non-zero drag coefficient given value is drag_coefficient = 0.0
PA0042	use_top_fluxes must be .TRUE. in ocean version
PA0043	ABS( alpha_surface = ... ) must be< 90.0
PA0044	dt = ... <= 0.0
PA0045	cfl_factor = ... out of range 0.0 < cfl_factor <= 1.0 is required
PA0046	baroclinicity (ug) not allowed simultaneously with galilei transformation
PA0047	baroclinicity (vg) not allowed simultaneously with galilei transformation
PA0048	variable translation speed used for galilei-transformation, which may cause instabilities in stably stratified regions
PA0049	unknown boundary condition: bc_lr = "..."
PA0050	unknown boundary condition: bc_ns = "..."
PA0051	non-cyclic lateral boundaries do not allow psolver = "..."
PA0052	non-cyclic lateral boundaries do not allow momentum_advec = "..."
PA0053	non-cyclic lateral boundaries do not allow scalar_advec = "..."
PA0054	non-cyclic lateral boundaries do not allow galilei_transformation = .T.
PA0055	adjust_mixing_length = TRUE and bc_e_b = "neumann"
PA0056	adjust_mixing_length = FALSE and bc_e_b = "..."
PA0057	boundary condition bc_e_b changed to "..."
PA0058	unknown boundary condition: bc_e_b = "..."
PA0059	unknown boundary condition: bc_p_b = "..."
PA0060	boundary condition: bc_p_b = "..." not allowed with prandtl_layer = .FALSE.
PA0061	unknown boundary condition: bc_p_t = "..."
PA0062	unknown boundary condition: bc_pt_b = "..."
PA0063	unknown boundary condition: bc_pt_t = "..."
PA0064	both, top_momentumflux_u AND top_momentumflux_v must be set
PA0065	boundary_condition: bc_pt_b = "..." is not allowed with constant_heatflux = .TRUE.
PA0066	constant_heatflux = .TRUE. is not allowed with pt_surface_initial_change (/=0) = ...
PA0067	boundary_condition: bc_pt_t = "..." is not allowed with constant_top_heatflux = .TRUE.
PA0068	unknown boundary condition: bc_sa_t = "..."
PA0069	boundary condition: bc_sa_t = "..." requires to set top_salinityflux
PA0070	boundary condition: bc_sa_t = "..." is not allowed with constant_top_salinityflux = .TRUE.'
PA0071	unknown boundary condition: bc_..._b ="..."
PA0072	unknown boundary condition: bc_..._t ="..."
PA0073	boundary condition: bc_..._b = "..." is not allowed with prescribed surface flux
PA0074	a prescribed surface flux is not allowed with ..._surface_initial_change (/=0) = ...
PA0075	boundary condition: bc_uv_b = "..." is not allowed with prandtl_layer = .TRUE.
PA0076	unknown boundary condition: bc_uv_b = "..."
PA0077	unknown boundary condition: bc_uv_t = "..."
PA0078	rayleigh_damping_factor = ... out of range [0.0,1.0]
PA0079	rayleigh_damping_height = ... out of range [0.0, ...]
PA0080	overshoot_limit_... < 0.0 is not allowed
PA0081	ups_limit_... < 0.0 is not allowed
PA0082	number of statistic_regions = ... but only 10 regions are allowed
PA0083	normalizing_region = ... must be >= 0 and <= ... (value of statistic_regions)
PA0084	dt_sort_particles is reset to 0.0 because of cloud_droplets = .TRUE.
PA0085	averaging_interval = ... must be <= dt_data_output = ...
PA0086	averaging_interval_pr = ... must be <= dt_dopr = ...
PA0087	averaging_interval_sp = ... must be <= dt_dosp = ...
PA0088	dt_averaging_input = ... must be <= averaging_interval = ...
PA0089	dt_averaging_input_pr = ... must be <= averaging_interval_pr = ...
PA0090	precipitation_amount_interval = ... must not be larger than dt_do2d_xy = ...
PA0091	data_output_pr = ... is not implemented for ocean = .FALSE.
PA0092	data_output_pr = ... is not implemented for humidity = .FALSE.
PA0093	data_output_pr = ... is not implemented for passive_scalar = .FALSE.
PA0094	data_output_pr = ... is not implemented for cloud_physics = .FALSE.
PA0095	data_output_pr = ... is not implemented for cloud_physics = .FALSE. and humidity = .FALSE.
PA0096	data_output_pr = ... is not implemented for cloud_physics = .FALSE. or cloud_droplets = .FALSE
PA0097	illegal value for data_output_pr or data_output_pr_user = "..."
PA0098	illegal value for data_output_pr = "..."
PA0100	unknown normalization method cross_normalized_x = "..."
PA0101	unknown normalization method cross_normalized_y = "..."
PA0102	number of output quantities given by data_output and data_output_user exceeds the limit of 100
PA0103	output of "..." requires constant_diffusion = .FALSE.
PA0104	output of "..." requires a "particles_par"-NAMELIST in the parameter file (PARIN)
PA0105	output of "..." requires humidity = .TRUE.
PA0106	output of "..." requires cloud_physics = .TRUE. or cloud_droplets = .TRUE.
PA0107	output of "..." requires cloud_droplets = .TRUE.
PA0108	output of "..." requires cloud_physics = .TRUE.
PA0109	output of "..." requires ocean = .TRUE.
PA0110	output of "..." requires passive_scalar = .TRUE.
PA0111	illegal value for data_output: "..." only 2d-horizontal cross sections are allowed for this value
PA0112	output of "..." requires precipitation = .TRUE.
PA0113	temporal averaging of precipitation amount "..." is not possible
PA0114	illegal value for data_output or data_output_user = "..."
PA0115	illegal value for data_output = "..."
PA0117	do3d_compress = .TRUE. not allowed on host "..."
PA0118	illegal precision: do3d_comp_prec ( ...) = "..."
PA0119	unknown variable "..." given for do3d_comp_prec(...)
PA0120	unknown value for data_output_format "..."
PA0121	km_constant = ... < 0.0
PA0122	prandtl_number = ... < 0.0
PA0123	prandtl_layer is not allowed with fixed value of km
PA0124	outflow_damping width out of range
PA0125	rif_min = ... must be less than rif_max = ...
PA0126	disturbance_level_b = ... must be >= ... (zu(3))
PA0127	disturbance_level_b = ... must be <= ... (zu(nzt-2))
PA0128	disturbance_level_t = ... must be <= ... (zu(nzt-2))
PA0129	disturbance_level_t = ... must be >= disturbance_level_b = ...
PA0130	disturbance_level_ind_t =... must be >= disturbance_level_b = ...
PA0131	inflow_disturbance_begin out of range
PA0132	inflow_disturbance_end out of range
PA0133	turbulent_inflow = .T. requires a Dirichlet condition at the inflow boundary
PA0134	illegal value for recycling_width: ...
PA0135	unknown random generator: random_generator = "..."
PA0136	damp_level_1d = ... must be > 0.0 and < ... (zu(nzt+1))
PA0137	mixing_length_1d = "..." is unknown
PA0138	dissipation_1d = "..." is unknown
PA0139	termination_time_needed = ... must be > 30.0 on host ...
PA0140	termination_time_needed = ... should be >= 300.0 on host "..."
PA0141	coupling requires PALM to be called with "mrun -K parallel"
PA0142	absolute temperature < 0.0 at zu(...) = ...
PA0143	k=... j=... i=... ql_c=... part(...)%wf=... delta_r=...
PA0144	#1 k=... j=... i=... e_s=... e_a=... t_int=... d_radius=... delta_r=... particle_radius=...
PA0145	collision_efficiency out of range: ...
PA0146	maximum_number_of_particles needs to be increased but this is not allowed with netcdf_data_format < 3	netCDF output is switched on (d3par = 'netcdf' ) and a netCDF3 format is used (d3par < 3).
PA0147
PA0148
PA0149
PA0150
PA0151
PA0152
PA0153
PA0154
PA0155
PA0156
PA0157
PA0158
PA0159
PA0160
PA0161
PA0162
PA0163
PA0164
PA0165
PA0166
PA0167
PA0168
PA0169
PA0170
PA0171
PA0172
PA0173
PA0174
PA0175
PA0176
PA0177
PA0178
PA0179
PA0180
PA0181
PA0182
PA0183
PA0184
PA0185
PA0186
PA0187
PA0188
PA0189
PA0190
PA0191
PA0192
PA0193
PA0194
PA0195
PA0196
PA0197
PA0198
PA0199
PA0200
PA0201
PA0202
PA0203
PA0204
PA0200