Changes between Version 577 and Version 578 of doc/app/errmsg

Timestamp:

Oct 2, 2018 2:04:44 AM (6 years ago)

Author:

raasch

Comment:

--

doc/app/errmsg

@@ -114 +114 @@
 ||[=#PA0089 PA0089]   ||dt_averaging_input_pr = ... must be <= averaging_interval_pr = ... ||The sampling interval (set by [../d3par#dt_averaging_input_pr dt_averaging_input_pr]) for averaging profile data must be less or equal to the averaging interval (set by [../d3par#averaging_interval_pr averaging_interval_pr]). Adjust settings of these variables appropriately in the parameter file. ||
 ||[=#PA0090 PA0090]   ||precipitation_amount_interval = ... must not be larger than dt_do2d_xy = ... ||Choose a value for [../d3par#precipitation_amount_interval precipitation_amount_interval] smaller than or equal to [../d3par#dt_do2d_xy dt_do2d_xy]. Adjust the settings of [../d3par#precipitation_amount_interval precipitation_amount_interval] appropriately in the parameter file.||
-||[=#PA0091 PA0091]   ||wrong component of Stokes force: ...  ||Only the three Cartesian components 1, 2, and 3 are allowed for the Stokes force in ocean mode.  ||
+||[=#PA0091 PA0091]   ||wrong component of Stokes force: ...  ||Only the two Cartesian components 2 and 3 are allowed for the Stokes force in ocean mode.  ||
 ||[=#PA0092 PA0092]   ||data_output_pr = ... is not implemented for humidity = .FALSE.   ||The listed entries in the parameter file under  [../d3par#data_output_pr data_output_pr] are only available for [../inipar#humidity humidity]= .T.. There could also be a typo in [../d3par#data_output_pr data_output_pr] (an output variable was used that does not exist in PALM). ||
 ||[=#PA0093 PA0093]   ||data_output_pr = ... is not implemented for passive_scalar = .FALSE.  ||The listed entries in the parameter file under  [../d3par#data_output_pr data_output_pr] are only available for [../inipar#passive_scalar passive_scalar]= .T.. There could also be a typo in [../d3par#data_output_pr data_output_pr] (an output variable was used that does not exist in PALM).||
@@ -688 +688 @@
 ||[=#PA0464 PA0464]   || file WTM_DATA does not exist  || Make sure that the file [../iofiles#WTM_DATA WTM_DATA] containing physical characteristics of the blades, as described in [[source:/palm/trunk/EXAMPLES/wind_turbine/example_wtm.txt| example_wtm.txt]], is provided in the INPUT folder of the respective run on the host where the job is running.  ||
 ||[=#PA0465 PA0465]   || surface_type = netcdf requires static input file.  || Either provide the file [../iofiles#PIDS_STATIC PIDS_STATIC] or change the value of [../lsmpar#surface_type surface_type] to a value different than netcdf. ||
-||[=#PA0466 PA0466]   || errors in wind_turbine_par-NAMELIST: some variables for steering may not be properly set  || See [../wind_turbine_par wind turbine parameter] for allowed values. ||
+||[=#PA0466 PA0466]   || wrong component of wave breaking: ...  || Only the two Cartesian components 1 and 2 are allowed for adding wave breaking effects in ocean mode. ||
 ||[=#PA0467 PA0467]   || y_shift /= 0 is only allowed for cyclic boundary conditions in both directions  || y_shift defines a shift in the cyclic boundary conditions. It can therefore only be used with cyclic boundary conditions. See [../inipar#y_shift y_shift]. ||
 ||[=#PA0468 PA0468]   || y_shift /= 0 is only allowed for multigrid pressure solvers  || y_shift defines a shift in the cyclic boundary conditions. The data then becomes not truly cyclic anymore. Therefore, the fft pressure solver is no longer viable. See [../inipar#y_shift y_shift]. ||