Home

Context Navigation

errmsg

Timestamp:: May 28, 2018 1:06:25 PM (7 years ago)
Author:: Giersch
Comment:: --

Legend:

: Unmodified
: Added
: Removed
: Modified

doc/app/errmsg

-                      v545
+                      v546
 ||[=#PA0293 PA0293]   || || Message number is unused. ||
 ||[=#PA0294 PA0294]   || || Message number is unused. ||
 ||[=#PA0295 PA0295]   || || Message number is unused. ||
+||[=#PA0295 PA0295]   || complex_terrain requires topography = 'read_from_file' || Self-explanatory. See [../inipar#complex_terrain complex_terrain] and [../inipar#topography topography]. ||
 ||[=#PA0296 PA0296]   ||version mismatch concerning binary_version_global: version on file = "..." version on program = "..."   || The precursor run was carried out with a different version than the main run. Repeat the precurser with the current version or carry out the main run with the same version as the precursor.  ||
 ||[=#PA0297 PA0297]   ||numprocs not found in data from prior run on PE ...   || Number of processors are not written out or read in correctly during restarts. Please submit a  [/newticket trouble ticket]. ||
 …
 ||[=#PA0355 PA0355]   ||netcdf_deflate out of range \\ given value: ..., allowed range: 0-9  ||Set d3par-parameter [../d3par#netcdf_deflate netcdf_deflate] to a value within the allowed range ||
 ||[=#PA0356 PA0356]   ||netcdf_deflate reset to 0  ||You have set [../d3par#netcdf_data_format netcdf_data_format] /= 3 and [../d3par#netcdf_deflate netcdf_deflate] > 0 in the d3par-NAMELIST. However, data compression only works for the NetCDF4/HDF5 non-parallel format ([../d3par#netcdf_data_format netcdf_data_format] = 3).  ||
 ||[=#PA0357 PA0357]   ||unknown cloud microphysics scheme cloud_scheme = "..."   || Unknown cloud microphysics scheme. Allowed [../inipar#cloud_scheme cloud] microphysics schemes are "saturation_adjust", "kessler", "seifert_beheng" or "morrison". ||
+||[=#PA0357 PA0357]   ||unknown cloud microphysics scheme cloud_scheme = "..."   || Unknown cloud microphysics scheme. Allowed [../inipar#cloud_scheme cloud microphysics] schemes are "saturation_adjust", "kessler", "seifert_beheng" or "morrison". ||
 ||[=#PA0358 PA0358]   ||data_output_pr = '...' is not implemented for cloud_scheme /= ... || Output of profiles of rain drop number density (nr) or rain water mixing ratio (qr) is only allowed for [../inipar#cloud_scheme cloud_scheme] = "seifert_beheng". Output of profiles of cloud drop number density (nc) is only allowed for [../inipar#cloud_scheme cloud_scheme] = "morrison". ||
 ||[=#PA0359 PA0359]   ||output of "..." requires cloud_scheme = seifert_beheng || Output of 3d-data, cross-sections or masked data of rain drop number concentration (nr) or rain water content (qr) is only allowed for [../inipar#cloud_scheme cloud_scheme] = "seifert_beheng". Output of cloud drop number density (nc) is only allowed for [../inipar#cloud_scheme cloud_scheme] = "morrison". ||
 …
 ||[=#PA0361 PA0361]   || output of ssws* requires passive_scalar=.TRUE.   || Variables connected with passive_scalar, e.g. like the resolved-scale turbulent scalar flux w*s*, can only be output if [../inipar#passive_scalar passive_scalar] = '''.TRUE.'''   ||
 ||[=#PA0362 PA0362]   || || Message number is unused. ||
 ||[=#PA0363 PA0363]   ||No time dependent surface variables in LSF_DATA for end of run found ||PALM detected an end-of-file condition for the surface values in [../../app/iofiles#LSF_DATA LSF_DATA] and aborts. Possible reasons could be that no time dependent surface variables are provided in the large scale forcing file.   ||
 ||[=#PA0364 PA0364]   ||zu(k) = ... m is higher than the maximum height in NUDING_DATA which is ...m. Interpolation on PALM grid is not possible. || [../../app/iofiles#NUDGING_DATA NUDGING_DATA] has a maximum vertical height that is smaller than the vertical extent of the grid used in PALM. Hence, interpolation of the NUDING_DATA onto the PALM grid is not possible. Reduce either the vertical extent of the PALM modeling domain or enlarge the NUDING_DATA file correspondingly. Note: it is also possible that your file [../../app/iofiles#NUDGING_DATA NUDGING_DATA] is not formatted correctly and that there has been an error while reading it. ||
+||[=#PA0363 PA0363]   ||No time dependent surface variables in LSF_DATA for end of run found ||PALM detected an end-of-file condition for the surface values in [../../app/iofiles#LSF_DATA LSF_DATA] and aborts. Possible reasons could be that no or too less time dependent surface variables are provided in the large scale forcing file.   ||
+||[=#PA0364 PA0364]   ||zu(k) = ... m is higher than the maximum height in NUDING_DATA which is ...m. Interpolation on PALM grid is not possible. || [../../app/iofiles#NUDGING_DATA NUDGING_DATA] has a maximum vertical height that is smaller than the vertical extent of the grid used in PALM. Hence, interpolation of the [../../app/iofiles#NUDGING_DATA NUDGING_DATA] onto the PALM grid is not possible. Reduce either the vertical extent of the PALM modeling domain or enlarge the NUDING_DATA file correspondingly. Note: it is also possible that your file [../../app/iofiles#NUDGING_DATA NUDGING_DATA] is not formatted correctly and that there has been an error while reading it. ||
 ||[=#PA0365 PA0365]   ||file NUDGING_DATA does not exist  ||Make sure that the file ''basename_nudge'' containing the nudging profiles as described in [../../app/iofiles#NUDGING_DATA NUDGING_DATA] is provided in the INPUT folder of the respective run on the host where the job is running.  ||
 ||[=#PA0366 PA0366]   ||errors in file NUDGING_DATA  ||PALM has problems reading the file ''basename_nudge''. Possible reasons could be that the format described in [../../app/iofiles#NUDGING_DATA NUDGING_DATA] is not followed closely. ||
 …
 ||[=#PA0459 PA0459]   || unknown aerosol type  'aero_type = ...'  ||Chose an appropriate value for [../parpar#aero_type aero_type]. ||
 ||[=#PA0460 PA0460]   || no wind_turbine_par-NAMELIST found: End of file has reached || Maybe you forgot to end the wind_turbine_par-NAMELIST with a backslash at the end of the _p3d-file. ||
 ||[=#PA0461 PA0461]   || pitch_control = .TRUE. requires speed_control = .TRUE. || ||
 ||[=#PA0462 PA0462]   || omega_rot < 0.0, Please set omega_rot to a value larger than or equal to zero || ||
 ||[=#PA0463 PA0463]   || rcx, rcy, rcz have to be given for each turbine. || ||
 ||[=#PA0464 PA0464]   || file WTM_DATA does not exist  || ||
 ||[=#PA0465 PA0465]   || surface_type = 'netcdf' is not supported at the moment'  ||It is planned to allow for setting up the land surface model entirely via a single NetCDF file. This approach will be available by the end of 2017. Until then, the land surface scheme must be steered via NAMELIST and user interface. ||
+||[=#PA0461 PA0461]   || pitch_control = .TRUE. requires speed_control = .TRUE. || Self-explanatory. See [../wind_turbine_par#pitch_control pitch_control] and [../wind_turbine_par#speed_control speed_control]. ||
+||[=#PA0462 PA0462]   || omega_rot < 0.0, Please set omega_rot to a value larger than or equal to zero || Self-explanatory. See [../wind_turbine_par#omega_rot omega_rot]. ||
+||[=#PA0463 PA0463]   || rcx, rcy, rcz have to be given for each turbine. || The position of each turbine has to be specified. See [../wind_turbine_par#rcx rcx], [../wind_turbine_par#rcy rcy] and [../wind_turbine_par#rcz rcz]. ||
+||[=#PA0464 PA0464]   || file WTM_DATA does not exist  || Make sure that the file [../iofiles#WTM_DATA WTM_DATA] containing physical characteristics of the blades, as described in [[source:/palm/trunk/EXAMPLES/wind_turbine/example_wtm.txt| example_wtm.txt]], is provided in the INPUT folder of the respective run on the host where the job is running.  ||
+||[=#PA0465 PA0465]   || surface_type = netcdf requires static input file.  || Either provide the file [../iofiles#PIDS_STATIC PIDS_STATIC] or change the value of [../lsmpar#surface_type surface_type] to a value different than netcdf. ||
 ||[=#PA0466 PA0466]   || errors in wind_turbine_par-NAMELIST: some variables for steering may not be properly set  || See [../wind_turbine_par wind turbine parameter] for allowed values. ||
 ||[=#PA0467 PA0467]   || y_shift /= 0 is only allowed for cyclic boundary conditions in both directions  || y_shift defines a shift in the cyclic boundary conditions. It can therefore only be used with cyclic boundary conditions. See [../inipar#y_shift]. ||
 ||[=#PA0468 PA0468]   || y_shift /= 0 is only allowed for multigrid pressure solvers  || y_shift defines a shift in the cyclic boundary conditions. The data then becomes not truly cyclic anymore. Therefore, the fft pressure solver is no longer viable. See [../inipar#y_shift]. ||
+||[=#PA0467 PA0467]   || y_shift /= 0 is only allowed for cyclic boundary conditions in both directions  || y_shift defines a shift in the cyclic boundary conditions. It can therefore only be used with cyclic boundary conditions. See [../inipar#y_shift y_shift]. ||
+||[=#PA0468 PA0468]   || y_shift /= 0 is only allowed for multigrid pressure solvers  || y_shift defines a shift in the cyclic boundary conditions. The data then becomes not truly cyclic anymore. Therefore, the fft pressure solver is no longer viable. See [../inipar#y_shift y_shift]. ||
 ||[=#PA0469 PA0469]   || unknown aerosol species for bulk microphysics  || aerosol species must be set to a known type. See [../inipar#aerosol_bulk aerosol_bulk]. ||
 ||[=#PA0470 PA0470]   || unknown aerosol species for lagrangian cloud microphysics  || aerosol species must be set to a known type. See [../parpar#aero_species aero_species]. ||
 ||[=#PA0471 PA0471]   ||  number of soil layers (...) does not match to the number of layers specified in soil_temperature (...) || For each soil layer an initial soil temperature must be prescribed (see [wiki:doc/app/lsmpar#soil_temperature soil_temperature]). ||
 ||[=#PA0472 PA0472]   || deep_soil_temperature is not set but must be /= 9999999.9 || Since r2729 the deep soil temperature is no longer part of the soil_temperature array and must be specific separately. The deep soil temperature serves as bottom boundary condition for heat diffusion in the soil model. Note that there is no analogous value for soil moisture as the bottom of the soil can either be set to bedrock (water accumulates) or free drainage (water is lost). ||
 ||[=#PA0473 PA0473]   || Vertical grid stretching is not allowed for complex_terrain = .T. ||  ||
+||[=#PA0472 PA0472]   || deep_soil_temperature is not set but must be /= 9999999.9 || Since r2729 the [../lsmpar#deep_soil_temperature deep_soil_temperature] is no longer part of the soil_temperature array and must be specific separately. The deep soil temperature serves as bottom boundary condition for heat diffusion in the soil model. Note that there is no analogous value for soil moisture as the bottom of the soil can either be set to bedrock (water accumulates) or free drainage (water is lost). ||
+||[=#PA0473 PA0473]   || Vertical grid stretching is not allowed for complex_terrain = .T. || Self-explanatory. See [../inipar#complex_terrain complex_terrain] and [../inipar#dz_stretch_level dz_stretch_level].  ||
 ||[=#PA0474 PA0474]   ||pavement_type = 0 (user_defined) requires setting of pavement_depth_level /= 0  ||When a user-defined pavement is prescribed, a depth must be asigned that determines how deep the pavement extends into the ground. The [../lsmpar#pavement_heat_capacity pavement heat capacity] and  [../lsmpar##pavement_heat_cond pavement heat conductivty] are then asigned to all those levels. ||
 ||[=#PA0475 PA0475]   ||  particle violated cfl criterion || this is that some of your particles moves too fast. ||
 ||[=#PA0476 PA0476]   ||  Humidity has to be set to .T. in the _p3d file for coupled runs between ocean and atmosphere. || Set humidity = .T. in the _p3d. ||
 ||[=#PA0477 PA0477]   ||  In Child model:  bc_par_t is automatically set to nested || Set bc_par_t = 3 in the child _p3d_NXX. ||
 ||[=#PA0478 PA0478]   ||  In Child model:  bc_par_lr is automatically set to nested || Set bc_par_lr = 3 in the child _p3d_NXX. ||
 ||[=#PA0479 PA0479]   ||  In Child model:  bc_par_ns is automatically set to nested || Set bc_par_ns = 3 in the child _p3d_NXX. ||
+||[=#PA0475 PA0475]   ||  Particle violated CFL-criterion: particle with id ... will be deleted! || This is a warning that some of your particles moves too fast. Therefore they will be deleted. ||
+||[=#PA0476 PA0476]   ||  Humidity has to be set to .T. in the _p3d file for coupled runs between ocean and atmosphere. || Set [../inipar#humidity humidity] = .T. in the _p3d. ||
+||[=#PA0477 PA0477]   ||  In Child model:  bc_par_t is automatically set to nested || This is a warning that [../parpar#bc_par_t bc_par_t] is automatically set to nested although a different boundary condition was specified. Set [../parpar#bc_par_t bc_par_t] = 'nested'  in the child _p3d_NXX. ||
+||[=#PA0478 PA0478]   ||  In Child model:  bc_par_lr is automatically set to nested || This is a warning that [../parpar#bc_par_lr bc_par_lr] is automatically set to nested although a different boundary condition was specified.. Set [../parpar#bc_par_lr bc_par_lr] = 'nested'  in the child _p3d_NXX. ||
+||[=#PA0479 PA0479]   ||  In Child model:  bc_par_ns is automatically set to nested || This is a warning that [../parpar#bc_par_ns bc_par_ns] is automatically set to nested although a different boundary condition was specified. Set [../parpar#bc_par_ns bc_par_ns] = 'nested'  in the child _p3d_NXX. ||
 ||[=#PA0480 PA0480]   ||  RMA window too small on child ||  ||
 ||[=#PA0481 PA0481]   ||  RMA window too small on parent ||  ||
+||[=#PA0482 PA0482]   ||  Version of binary SVF file "..." does not match the version of model "..." ||  ||
+||[=#PA0483 PA0483]   ||  Wrong number of SVF or CSF ||  ||
+||[=#PA0484 PA0484]   ||  Wrong structure of binary svf file ||  ||
+||[=#PA0485 PA0485]   ||  dissipation_1d = "as_in_3d_model" requires mixing_length_1d = "as_in_3d_model" || The dissipation rate within the 1D model can be calculated the same way as in the 3D model only if the mixing length is also calculated as in the 3D model. ||
+||[=#PA0486 PA0486]   ||  Usage of radiation module is only allowed if land-surface and/or urban-surface model is applied. || ||
+||[=#PA0487 PA0487]   ||  namelist ... is deprecated and will be removed in near future. Please &use namelist ... instead' ||An outdated namelist name was found in the parameter file. This will still work until the next PALM release, but it is recommended to switch to the new namelist name. ||
+||[=#PA0488 PA0488]   ||   || ||
+||[=#PA0489 PA0489]   || In case of nesting, spinup_time and dt_spinup must be identical in all parent and child domains. || ||
+||[=#PA0490 PA0490]   || nsurfl from SVF file does not match calculated nsurfl from radiation_interaction_init. || Number of surface elements in sky-view factor file does not match the calculated number of surface elements. ||
+||[=#PA0491 PA0491]   || A different number of processors between the run that has written the svf data and the one that will read it is not allowed. || ||
+||[=#PA0492 PA0492]   || initializing_actions = "..." has been changed to 'set_constant_profiles' in child domain. || In a nested run, only 'read_restart_data' (in case of a restart) or 'set_constant_profiles' are allowed in child domain.  ||
+||[=#PA0482 PA0482]   ||  Version of binary SVF file "..." does not match the version of model "..." || This error occurs when radiation data from the file SVFIN is read and the precursor run was carried out with a different svf binary version than the main run. Repeat the precurser with the current version or carry out the main run with the same version as the precursor. You can check the svf binary version number which is required for the main run in [[source:palm/trunk/SOURCE/radiation_model_mod.f90| radiation_model_mod.f90]].  ||
+||[=#PA0483 PA0483]   ||  Wrong number of SVF or CSF || This error can happen if svf data is read from file SVFIN (e.g. during manual restarts). The local number of sky view factors and canopy sink factors for calculating surface reflection of radiation has to be the same between the precursor run and the main run. Be sure that you create the svf binary data with the same version as the version of the main run. ||
+||[=#PA0484 PA0484]   ||  || Message number is unused. ||
+||[=#PA0485 PA0485]   ||  dissipation_1d = "as_in_3d_model" requires mixing_length_1d = "as_in_3d_model" || The [../inipar#dissipation_1d dissipation rate] in the TKE equation of the 1d-model can be calculated the same way as in the 3D model only if the [../inipar#mixing_length_1d mixing_length] is also calculated as in the 3D model. ||
+||[=#PA0486 PA0486]   ||  Usage of radiation module is only allowed if land-surface and/or urban-surface model is applied. || Either the namelist &land_surface_parameters has to be set in the _p3d file or &urban_surface_parameters (or both) to avoid this error. ||
+||[=#PA0487 PA0487]   ||  namelist ... is deprecated and will be removed in near future. Please use namelist ... instead' ||An outdated namelist name was found in the parameter file. This will still work until the next PALM release, but it is recommended to switch to the new namelist name. ||
+||[=#PA0488 PA0488]   || ERROR: the surface type ... is not supported for calculating SVF || Allowed surface types are 0, 2, 3, 4, 5, 6, 7, 8, 9, 10. Their meaning can be identified in [[source:palm/trunk/SOURCE/radiation_model_mod.f90| radiation_model_mod.f90]]. This error should not occur. Please submit a [/newticket trouble ticket]. ||
+||[=#PA0489 PA0489]   || In case of nesting, spinup_time and dt_spinup must be identical in all parent and child domains. || In case of spinup and nested run, the spinup end time must be identical in order to have synchronously running simulations. Adjust [../inipar#spinup_time spinup_time] and/or [../inipar#dt_spinup dt_spinup] in your steering files appropriately. ||
+||[=#PA0490 PA0490]   || nsurfl from SVF file does not match calculated nsurfl from radiation_interaction_init. || Number of all local surface elements in sky-view factor file (SVFIN) does not match the calculated number of local surface elements. Be sure that you created the svf binary data with the same version as the version of the main run and that you did not introduce further surfaces in the meantime. Otherwise submit a [/newticket trouble ticket]. ||
+||[=#PA0491 PA0491]   || A different number of processors between the run that has written the svf data and the one that will read it is not allowed. || Self-explanatory. ||
+||[=#PA0492 PA0492]   || initializing_actions = "..." has been changed to 'set_constant_profiles' in child domain. || This is an informative message. In a nested run, only 'read_restart_data' (in case of a restart) or 'set_constant_profiles' are allowed for [../inipar#initializing_actions initializing_actions] in child domain even though the constant-profiles initializations for the prognostic variables will be overwritten by pmci_child_initialize and pmci_parent_initialize. This is, however, important e.g. to make sure that diagnostic variables are set properly. An exception is made in case of restart runs and if user decides to do everything by its own.  ||
+||[=#PA0493 PA0493]   || npcbl from SVF file does not match calculated npcbl from radiation_interaction_init || The number of the local plant canopy gridboxes in SVFIN does not match the one which is calculated during model initialization. Be sure that you created the svf binary data with the same version as the version of the main run. Otherwise submit a [/newticket trouble ticket].  ||
+||[=#PA0494 PA0494]   || ndsidir from SVF file does not match calculated ndsidir from radiation_presimulate_solar_pos || The number of apparent solar directions in SVFIN does not match the one which is calculated during model initialization. Be sure that you created the svf binary data with the same version as the version of the main run. Otherwise submit a [/newticket trouble ticket]. ||
 ||[=#UI0001 UI0001]   ||unknown location "..."   ||The location has to be one of 'before_timestep', 'after_integration', 'after_timestep', 'u_tendency' 'v_tendency', 'w_tendency', 'pt_tendency', 'sa_tendency', 'e_tendency', 'q_tendency', 's_tendency'.  ||
 ||[=#UI0002 UI0002]   ||location "..." is not allowed to be called with parameters "i" and "j"   || ** ||