Home


About us
PALM
PALM-4U
Installation
Release notes
Documentation
Getting Help
Gallery
Developers area

Changes between Version 511 and Version 512 of doc/app/errmsg


Ignore:
Timestamp:
May 22, 2018 2:54:54 PM (6 years ago)
Author:
Giersch
Comment:

--

Legend:

Unmodified
Added
Removed
Modified

  • doc/app/errmsg

    v511 v512  
    4040||[=#PA0015 PA0015]   || Using synthetic turbulence generator requires initializing_actions = "set_constant_profiles" or "read_restart_data" || When switching on the synthetic turbulence generator by setting use_synthetic_turbulence_generator = .TRUE., PALM has to be initialized using either constant profiles ([../inipar#initializing_actions initializing_actions] = "set_constant_profiles") or loading data from a previous run ([../inipar#initializing_actions initializing_actions] = "read_restart_data"). Other initialization actions do not support the synthetic turbulence generator. ||
    4141||[=#PA0016 PA0016]   ||unknown solver for perturbation pressure: psolver = "..."   ||See parameter [../inipar#psolver psolver] for allowed values, and correct your parameter file. ||
    42 ||[=#PA0017 PA0017]   || ||message number is unused  ||
    43 ||[=#PA0018 PA0018]   || ||message number is unused  ||
     42||[=#PA0017 PA0017]   || ||message number is unused.  ||
     43||[=#PA0018 PA0018]   || ||message number is unused.  ||
    4444||[=#PA0019 PA0019]   || unknown surface type: surface_type = "..."  ||See parameter [../lsmpar#surface_type surface_type] for allowed values, and appropriately correct your parameter file. ||
    4545||[=#PA0020 PA0020]   ||unknown multigrid cycle: cycle_mg = "..."   ||See parameter [../inipar#cycle_mg cycle_mg] for allowed values, and appropriately correct your parameter file. ||
    … …  
    107107||[=#PA0082 PA0082]   ||number of statistic_regions = ... is not allowed ||Adjust parameter [../inipar#statistic_regions statistic_regions] in your parameter file to a value >= ''0''.  ||
    108108||[=#PA0083 PA0083]   ||normalizing_region = ... must be >= 0 and <= ... (value of statistic_regions)  ||The region number given by [../d3par#normalizing_region normalizing_region] must be within the range [0, [../inipar#statistic_regions statistic_regions] ]. Adjust [../d3par#normalizing_region normalizing_region] appropriately in your parameter file. ||
    109 ||[=#PA0084 PA0084]   || ||message number is unused ||
     109||[=#PA0084 PA0084]   || ||message number is unused. ||
    110110||[=#PA0085 PA0085]   ||averaging_interval = ... must be <= dt_data_output_av = ... ||The [../d3par#averaging_interval averaging_interval] for averaged output data must be smaller or equal to the output interval given by [../d3par#dt_data_output dt_data_output] or [../d3par#dt_data_output_av dt_data_output_av]. Adjust settings of these variables appropriately in the parameter file. ||
    111111||[=#PA0086 PA0086]   ||averaging_interval_pr = ... must be <= dt_dopr = ... ||The [../d3par#averaging_interval_pr averaging_interval_pr] for profile output data must be smaller or equal to the output interval given by [../d3par#dt_dopr dt_dopr]. Adjust settings of these variables appropriately in the parameter file. ||
    … …  
    127127||[=#PA0102 PA0102]   ||number of output quantities given by data_output and data_output_user exceeds the limit of 500   || The total number of output quantities listed in [../d3par#data_output data_output]  and [../userpar#data_output_user data_output_user] exceeds the maximum of 500. To increase this limit, the standard PALM code has to be modified. In case you have little experience with the PALM code use a [/newticket trouble ticket] for a query to increase the maximum output number.    ||
    128128||[=#PA0103 PA0103]   ||output of "e" requires constant_diffusion = .FALSE.   ||Output of the subgrid TKE e listed in the parameter file under [../d3par#data_output data_output] or [../d3par#data_output_masks data_output_masks] is only available for [../inipar#constant_diffusion constant diffusion]= .F.. ||
    129 ||[=#PA0104 PA0104]   ||output of "..." requires a "particles_par"-NAMELIST in the parameter file (PARIN)   ||Output of the particle concentration pc and/or particle radius pr listed in the parameter file under [../d3par#data_output data_output] or [../d3par#data_output_masks data_output_masks] is only available in case the [http://palm.muk.uni-hannover.de/wiki/doc/app/parpar particles_par] namelist ist set in the parameter file  ||
    130 ||[=#PA0105 PA0105]   ||output of "..." requires humidity = .TRUE.   ||Output of humidity (q and/or qv) listed in the parameter file under [../d3par#data_output data_output] or [../d3par#data_output_masks data_output_masks] is only available for [../inipar#humidity humidity]= .T.. ||
     129||[=#PA0104 PA0104]   ||output of "..." requires a "particles_par"-NAMELIST in the parameter file (PARIN)   ||Output of the particle concentration pc and/or particle radius pr listed in the parameter file under [../d3par#data_output data_output] or [../d3par#data_output_masks data_output_masks] is only available in case the [http://palm.muk.uni-hannover.de/wiki/doc/app/parpar particles_par] namelist is set in the parameter file  ||
     130||[=#PA0105 PA0105]   ||output of "..." requires humidity = .TRUE.   ||Output of humidity (q and/or vpt) listed in the parameter file under [../d3par#data_output data_output] or [../d3par#data_output_masks data_output_masks] is only available for [../inipar#humidity humidity]= .T.. ||
    131131||[=#PA0106 PA0106]   ||output of "ql" requires cloud_physics = .TRUE. or cloud_droplets = .TRUE.  ||Output of liquid water content ql listed in the parameter file under [../d3par#data_output data_output] or [../d3par#data_output_masks data_output_masks] is only available for [../inipar#humidity cloud_physics]= .T. or [../inipar#cloud_droplets cloud_droplets]= .T..  ||
    132132||[=#PA0107 PA0107]   ||output of "..." requires cloud_droplets = .TRUE.   || The quantities ql_c, ql_v, ql_vp are only calculated in case of [../inipar#cloud_droplets cloud_droplets] = ''.T.''.  ||
    133133||[=#PA0108 PA0108]   ||output of "..." requires cloud_physics = .TRUE.   || For the output of some quantities related to clouds and humidity [../inipar#cloud_physics cloud_physics] = ''.T.'' must be set. For example, the water vapor mixing ratio qv requires [../inipar#cloud_physics cloud_physics] = ''.T.''. Also, [../inipar#humidity humidity] = ''.T.'' must be set. If you want to simulate the humidity without condensation/evaporation processes, use only [../inipar#humidity humidity] = ''.T.'' and choose output quantity q for output of the water vapor mixing ratio.  ||
    134 ||[=#PA0109 PA0109]   ||output of "..." requires ocean = .TRUE.   || The quantities rho and sa are only calculated in case of [../inipar#ocean ocean] = ''.T.''. ||
     134||[=#PA0109 PA0109]   ||output of "..." requires ocean = .TRUE.   || The quantities rho_ocean and sa are only calculated in case of [../inipar#ocean ocean] = ''.T.''. ||
    135135||[=#PA0110 PA0110]   ||output of "s" requires passive_scalar = .TRUE.   || The output of the passive scalar s is only available if the prognostic equation for a passive scalar is solved by setting [../inipar#passive_scalar passive_scalar] = ''.T.''. ||
    136136||[=#PA0111 PA0111]   ||illegal value for data_output: "..." only 2d-horizontal cross sections are allowed for this value   ||The listed quantities are pure two-dimensional xy-cross-sections. They are not available as 3d data or xz/yz cross-sections. Note that these quantities are always marked by an asterisk as last character. See also [../d3par#data_output data_output].  ||
    … …  
    139139||[=#PA0114 PA0114]   ||illegal value for data_output or data_output_user = "..."   || No matching variable was found for the given identifier in the parameter file. Possible reasons are: (a) a typo in the parameter file, (b) a user-defined variable has not been defined in {{{user_check_data_output.f90}}}, (c) the string length of the user-defined variable exceeds the current limits (see [../userint/output here]). ||
    140140||[=#PA0115 PA0115]   ||illegal value for data_output = "..."   || No matching variable was found for the given identifier in the parameter file. This error is most likely related to a typo in the parameter file (a output variable was used that does not exist in PALM). For possible output quantities see [../d3par#data_output data_output]. ||
     141||[=#PA0116 PA0116]   ||  || message number is unused.  ||
    141142||[=#PA0117 PA0117]   ||pointer for array ".." can't be associated   ||This is an internal error message from the pmc (PALM model coupler) which is responsible for data exchange in nested runs. Please submit a trouble ticket if you are sure that you did not modify the source code of the model coupler ({{{pmc_interface_mod.f90}}}).  ||
    142143||[=#PA0118 PA0118]   ||using the beta function for the construction of the leaf area density profile requires both alpha_lad and beta_lad to be /= 9999999.9 ||If the lad (leaf area density) profile of a vegetation canopy is to be constructed using a beta distribution, parameters [/wiki/doc/app/canpar#alpha_lad alpha_lad], [/wiki/doc/app/canpar#beta_lad beta_lad] must be set and [/wiki/doc/app/canpar#lai_beta lai_beta] must be given a non-zero value. ||
    … …  
    196197||[=#PA0154 PA0154]   ||unknown conserve_volume_flow_mode: ...   || See parameter [../inipar#conserve_volume_flow_mode conserve_volume_flow_mode] for allowed values, and appropriately correct your parameter file.  ||
    197198||[=#PA0155 PA0155]   ||noncyclic boundary conditions require conserve_volume_flow_mode = "initial_profiles"   || See parameter [../inipar#conserve_volume_flow_mode conserve_volume_flow_mode] for allowed values. [../inipar#conserve_volume_flow_mode conserve_volume_flow_mode] = 'bulk_velocity' is not allowed when you are using non-cyclic boundary conditions.  ||
    198 ||[=#PA0156 PA0156]   ||   ||   message number is unused ||
     199||[=#PA0156 PA0156]   ||   ||   message number is unused. ||
    199200||[=#PA0157 PA0157]   ||nonzero bulk velocity requires conserve_volume_flow = .T. and conserve_volume_flow_mode = "bulk_velocity"   || The bulk velocity is used to prescribe a volume flow which then should be conserved. This, however, requires [../inipar#conserve_volume_flow conserve_volume_flow] = .T. and [../inipar#conserve_volume_flow_mode conserve_volume_flow_mode] = "bulk_velocity". ||
    200201||[=#PA0158 PA0158]   ||no vertical boundary condition for variable "..."   || Routine {{{advec_s_bc}}} was called for a variable, which does not have a specific boundary condition implemented. ||
    … …  
    256257||[=#PA0214 PA0214]   ||version mismatch concerning data from prior run version on file = ... version in program = ...   || This error occurs when particle data from the [../iofiles#PARTICLE_RESTART_DATA_OUT restart file] is read and the precursor run was carried out with a different particle binary version than the main run. Repeat the precurser with the current version or carry out the main run with the same version as the precursor. You can check the particle binary version number which is required for the main run in {{{lpm_read_restart_file.f90}}}.  ||
    257258||[=#PA0215 PA0215]   ||particle group # ... has a density ratio /= 0 but radius = 0   || Particles with mass but without radius are not allowed. Please  appropriately correct [../parpar#radius radius] or [../parpar#density_ratio density_ratio] ||
    258 ||[=#PA0216 PA0216]   ||   ||message number is unused ||
     259||[=#PA0216 PA0216]   ||   ||message number is unused. ||
    259260||[=#PA0217 PA0217]   ||unknown boundary condition bc_par_b = "..."   || See parameter [../parpar#bc_par_b bc_par_b] for allowed values, and appropriately correct your parameter file.  ||
    260261||[=#PA0218 PA0218]   ||unknown boundary condition bc_par_t = "..."   || See parameter [../parpar#bc_par_t bc_par_t] for allowed values, and appropriately correct your parameter file.  ||
    … …  
    264265||[=#PA0222 PA0222]   ||if the processor topology is prescribed by the user, both values of "npex" and "npey" must be given in the NAMELIST-parameter file   || In case that only one number of processors along x- or y- direction [../d3par#npex npex] or [../d3par#npey npey] is set in the [../d3par#pgrid &runtime_parameters-Namelist], the remaining, so far not assigned, number of processors has to be set, too.   ||
    265266||[=#PA0223 PA0223]   ||errors in \$nestpar   ||An unvalid variable name or value has been given in the nestpar-NAMELIST. Carefully check your nestpar-NAMELIST and compare with the parameters given and explained in the [wiki:doc/app/nestpar Nesting]-section of the model steering parameters.  ||
    266 ||[=#PA0224 PA0224]   ||   || message number is unused ||
     267||[=#PA0224 PA0224]   ||   || message number is unused. ||
    267268||[=#PA0225 PA0225]   ||x-direction: gridpoint number (...) is not an integral divisor of the number of processors (...)   || The division of the number of grid points along the x-direction given by [../inipar#nx nx]+1 by the number of processors along the x-direction has a rest and is therefore not an integral divisor of the number of processors. To solve this problem you must ensure that the aforementioned division is without rest for example by setting the number of PEs in y-direction manually (see [../d3par#npex npex]) or by changing [../inipar#nx nx]. It might also be the case that you did not think about that [../inipar#nx nx]+1 is the total number of gridpoints along the x-direction instead of [../inipar#nx nx]. ||
    268269||[=#PA0226 PA0226]   ||x-direction: nx does not match the requirements given by the number of PEs used please use nx = ... instead of nx =...   || ** ||
                                                                                                                                                                                                                                                                                                                                                                               
  | Impressum | ©Leibniz Universität Hannover |