Changes between Version 366 and Version 367 of doc/app/errmsg

Timestamp:

Jun 8, 2017 7:28:32 AM (8 years ago)

Author:

Giersch

Comment:

--

doc/app/errmsg

@@ -166 +166 @@
 }}}
 ||[=#PA0125 PA0125]   ||zeta_min = ... must be less than zeta_max = ...   ||The stability parameter {{{zeta=z_mo/L}}} ({{{z_mo}}}: height of the constant flux layer, {{{L}}}: Obukhov length) that is calculated interactively in PALM can be limited to prevent reaching unrealistic values under certain circumstances. Make sure that [../inipar#zeta_min zeta_min] is smaller than  [../inipar#zeta_max zeta_max]. ||
-||[=#PA0126 PA0126]   ||disturbance_level_b = ... must be >= ... (zu(3))    ||Due to technical reasons the lower disturbance level given by [../d3par#disturbance_level_b disturbance_level_b] has to be larger than zu(3). ||
-||[=#PA0127 PA0127]   ||disturbance_level_b = ... must be <= ... (zu(nzt-2))    ||Due to technical reasons the lower disturbance level given by [../d3par#disturbance_level_b disturbance_level_b] has to be smaller than zu(nzt-2).   ||
-||[=#PA0128 PA0128]   ||disturbance_level_t = ... must be <= ... (zu(nzt-2))    ||Due to technical reasons the upper disturbance level given by [../d3par#disturbance_level_t disturbance_level_t] has to be smaller than zu(nzt-2).  ||
-||[=#PA0129 PA0129]   ||disturbance_level_t = ... must be >= disturbance_level_b = ...    ||Ensure that [../d3par#disturbance_level_t disturbance_level_t]  is larger than [../d3par#disturbance_level_b disturbance_level_b] to obtain at least one layer where disturbances are added. ||
+||[=#PA0126 PA0126]   ||disturbance_level_b = ... must be >= ... (zu(3))    ||Due to technical reasons the lower disturbance level given by [../d3par#disturbance_level_b disturbance_level_b] has to be larger than or equal zu(3). ||
+||[=#PA0127 PA0127]   ||disturbance_level_b = ... must be <= ... (zu(nzt-2))    ||Due to technical reasons the lower disturbance level given by [../d3par#disturbance_level_b disturbance_level_b] has to be smaller than or equal zu(nzt-2).   ||
+||[=#PA0128 PA0128]   ||disturbance_level_t = ... must be <= ... (zu(nzt-2))    ||Due to technical reasons the upper disturbance level given by [../d3par#disturbance_level_t disturbance_level_t] has to be smaller than or equal zu(nzt-2).  ||
+||[=#PA0129 PA0129]   ||disturbance_level_t = ... must be >= disturbance_level_b = ...    ||Ensure that [../d3par#disturbance_level_t disturbance_level_t]  is larger than or equal [../d3par#disturbance_level_b disturbance_level_b] to obtain at least one layer where disturbances are added. ||
 ||[=#PA0130 PA0130]   ||disturbance_level_ind_t =... must be >= disturbance_level_b = ...    ||This error may occur when the lower and upper disturbance levels [../d3par#disturbance_level_b disturbance_level_b]  and [../d3par#disturbance_level_t disturbance_level_t]  are calculated automatically and there are two few grid points in the vertical direction. There have to be at least seven vertical levels. ||
 ||[=#PA0131 PA0131]   ||inflow_disturbance_begin out of range    || The parameter [../inipar#inflow_disturbance_begin inflow_disturbance_begin] gives the number of grid points (counted horizontally from the inflow) from which on perturbations are imposed on the horizontal velocity field. This value must not be smaller than zero or larger than nx (in case of non-cyclic lateral boundary conditions along the x-direction) or ny (in case of non-cyclic lateral boundary conditions along the y-direction). ||