Changes between Version 191 and Version 192 of doc/app/errmsg

Timestamp:

Sep 24, 2014 1:35:08 PM (11 years ago)

Author:

maronga

Comment:

--

doc/app/errmsg

@@ -350 +350 @@
 ||[=#PA0308 PA0308]   ||statistic regions on restart data file differ from the current run statistic regions on file = "..." statistic regions from run = "..." statistic data may be lost!  ||  ||
 ||[=#PA0309 PA0309]   ||inflow profiles not temporally averaged. Averaging will be done now using ... samples.   ||  ||
-||[=#PA0310 PA0310]   ||remote model "..." terminated with terminate_coupled_remote = ... local model "..." has terminate_coupled = ...   ||  ||
+||[=#PA0310 PA0310]   ||remote model "..." terminated with terminate_coupled_remote = ... local model "..." has terminate_coupled = ...   ||The remote model in a coupled run has been terminated. The reason for the termination is provided by {{{terminate_coupled}}}.\\\\Termination reasons:\\1 model was terminated (unknown reason)\\2 time step has reached minimum limit (see [#PA0312 PA0312])\\3 run will be terminated because it is running out of job cpu limit remaining time (see [#PA0163 PA0163])\\4 run will be terminated due to user settings of {{{dt_restart}}} (see [#PA0164 PA0164])\\5 run will be terminated due to user settings of {{{restart_time}}} (see [#PA0164 PA0164])\\6 unscheduled termination was forced by the user (see [#PA0398 PA0398]) ||
 ||[=#PA0311 PA0311]   ||number of gridpoints along x or/and y contain illegal factors only factors 8,6,5,4,3,2 are allowed   ||In case that [../inipar#fft_method fft_method]='temperton-algorithm', the number of horizontal grid points ([../inipar#nx nx]+1, [../inipar#ny ny]+1) must be composed of prime factors 2,3 and 5. Higher prime factors such as 7 are not allowed. Please ensure that these restrictions are fulfilled or use 'singleton-algorithm' as [../inipar#fft_method fft_method].  ||
 ||[=#PA0312 PA0312]   ||Time step has reached minimum limit. \\dt = ... s Simulation is terminated.\\old_dt = ... s\\dt_u = ... s\\dt_v = ... s\\dt_w = ... s\\dt_diff = ... s\\u_max = ... m/s k=... j=... i=...\\v_max = ... m/s k=... j=... i=...\w_max = ... m/s k=... j=... i=...   ||The time step is determined according to the CFL criterion to assure a stable numerical solution. This error message means that the required minimum time step, determined from the three velocity components, is several orders of magnitude smaller than [../d3par#dt_max dt_max]. Due to the large number of complex reasons it should be noted that this list is not complete, but it is intended to give general hints how to proceed in case of this error message. First, check for a unrealistic value of [../d3par#dt_max dt_max] in the NAMELIST file. Moreover, this error message may indicate for unrealistic settings of e.g. [../inipar#bc boundary conditions] or other NAMELIST parameters. For very small vertical grid spacing [../inipar#dz dz] this error might also occur if [../inipar#roughness_length roughness_length] >= [../inipar#dz dz]. Please also check if this error appears if you run without USERCODE. To compile and run the PALM and USERCODE with DEBUG-options might also give sometimes valuable hints. 
@@ -627 +627 @@
 ||[=#PA0396 PA0396]   ||The usage of use_subsidence_tendencies requires large_scale_subsidence = .T.. || If use_subsidence_tendencies is used, subsidence tendencies for temperature and humidity are read in from the external file LSF_DATA. However, these tendencies can only be applied to the prognostic variables if [../inipar#large_scale_subsidence large_scale_subsidence] = .T.. ||
 ||[=#PA0397 PA0397]   ||The usage of use_subsidence_tendencies requires large_scale_forcing = .T.. || If use_subsidence_tendencies is used, subsidence tendencies for temperature and humidity are read in from the external file LSF_DATA. This requires [../inipar#large_scale_forcing large_scale_forcing] = .T.. ||
+||[=#PA0398 PA0398]   ||run will be terminated because user forced a job finialization using a flag file: DO_STOP_NOW: "..." DO_RESTART_NOW: "..." ||The user can force an unscheduled termination/restart of the running job by creating one of the flag files {{{DO_STOP_NOW}}} or {{{DO_RESTART_NOW}}} in the temporary directory of the job. ||
 ||[=#UI0001 UI0001]   ||unknown location "..."   ||The location has to be either 'time_int' or 'nudging'.  ||
 ||[=#UI0002 UI0002]   ||location "..." is not allowed to be called with parameters "i" and "j"   ||  ||