source: palm/trunk/SOURCE/parin.f90 @ 818

 SUBROUTINE parin

!------------------------------------------------------------------------------!
! Current revisions:
! -----------------
!
!
! Former revisions:
! -----------------
! $Id: parin.f90 810 2012-01-30 13:40:12Z maronga $
!
! 809 2012-01-30 13:32:58Z maronga
! Bugfix: replaced .AND. and .NOT. with && and ! in the preprocessor directives
!
! 807 2012-01-25 11:53:51Z maronga
! New cpp directive "__check" implemented which is used by check_namelist_files
!
! 785 2011-11-28 09:47:19Z raasch
! +scalar_rayleigh_damping in inipar
!
! 767 2011-10-14 06:39:12Z raasch
! +u_profile, v_profile, uv_heights in inipar
!
! 759 2011-09-15 13:58:31Z raasch
! +maximum_parallel_io_streams in envpar,
! splitting of parallel I/O in blocks of PEs
!
! 683 2011-02-09 14:25:15Z raasch
! +synchronous_exchange in d3par
!
! 667 2010-12-23 12:06:00Z suehring/gryschka
! Steering parameter dissipation_control added in inipar. (commented out)
!
! 622 2010-12-10 08:08:13Z raasch
! +collective_wait in inipar
!
! 600 2010-11-24 16:10:51Z raasch
! parameters moved from d3par to inipar: call_psolver_at_all_substeps,
! cfl_factor, cycle_mg, mg_cycles, mg_switch_to_pe0_level, ngsrb, nsor,
! omega_sor, prandtl_number, psolver, rayleigh_damping_factor,
! rayleigh_damping_height, residual_limit
!
! 580 2010-10-05 13:59:11Z heinze
! Renaming of ws_vertical_gradient to subs_vertical_gradient and
! ws_vertical_gradient_level to subs_vertical_gradient_level
!
! 553 2010-09-01 14:09:06Z weinreis
! parameters for masked output are replaced by arrays
!
! 493 2010-03-01 08:30:24Z raasch
! +netcdf_data_format in d3par, -netcdf_64bit, -netcdf_64bit_3d
!
! 449 2010-02-02 11:23:59Z raasch
! +wall_humidityflux, wall_scalarflux
! +ws_vertical_gradient, ws_vertical_gradient_level
!
! 410 2009-12-04 17:05:40Z letzel
! masked data output: + dt_domask, mask_01~20_x|y|z, mask_01~20_x|y|z_loop, 
! mask_scale_x|y|z, masks, skip_time_domask
!
! 291 2009-04-16 12:07:26Z raasch
! +local_dvrserver_running in envpar
! Output of messages replaced by message handling routine.
! +canyon_height, canyon_width_x, canyon_width_y, canyon_wall_left, 
! canyon_wall_south, conserve_volume_flow_mode, coupling_start_time,
! dp_external, dp_level_b, dp_smooth, dpdxy, u_bulk, v_bulk in inipar
! topography_grid_convention moved from userpar
!
! 197 2008-09-16 15:29:03Z raasch
! +cthf,leaf_surface_concentration, scalar_exchange_coefficient
! +inflow_damping_height, inflow_damping_width, recycling_width,
! turbulent_inflow in inipar, -skip_time_dosp in d3par,
! allocation of hom_sum moved from init_3d_model to here,
! npex, npey moved from inipar to d3par, setting of myid_char_14 removed,
! lad is allways allocated
!
! 138 2007-11-28 10:03:58Z letzel
! +canopy_mode, drag_coefficient, lad_surface, lad_vertical_gradient, 
! lad_vertical_gradient_level, pch_index, plant_canopy, 
! +allocation of leaf area density field
!
! 108 2007-08-24 15:10:38Z letzel
! +e_init, top_momentumflux_u|v in inipar, +dt_coupling in d3par
!
! 95 2007-06-02 16:48:38Z raasch
! +bc_sa_t, bottom_salinityflux, ocean, sa_surface, sa_vertical_gradient,
! sa_vertical_gradient_level, top_salinityflux in inipar,
! sa_init is allocated
!
! 87 2007-05-22 15:46:47Z raasch
! Size of hom increased by the maximum number of user-defined profiles,
! var_hom renamed pr_palm
!
! 82 2007-04-16 15:40:52Z raasch
! +return_addres, return_username in envpar
!
! 75 2007-03-22 09:54:05Z raasch
! +dt_max, netcdf_64bit_3d, precipitation_amount_interval in d3par,
! +loop_optimization, pt_reference in inipar, -data_output_ts,
! moisture renamed humidity
!
! 20 2007-02-26 00:12:32Z raasch
! +top_heatflux, use_top_fluxes in inipar
!
! 3 2007-02-13 11:30:58Z raasch
! +netcdf_64bit_3d in d3par,
! RCS Log replace by Id keyword, revision history cleaned up
!
! Revision 1.57  2007/02/11 13:11:22  raasch
! Values of environment variables are now read from file ENVPAR instead of
! reading them with a system call, + NAMELIST envpar
!
! Revision 1.1  1997/07/24 11:22:50  raasch
! Initial revision
!
!
! Description:
! ------------
! This subroutine reads variables controling the run from the NAMELIST files
!------------------------------------------------------------------------------!

    USE arrays_3d
    USE averaging
    USE control_parameters
    USE dvrp_variables
    USE grid_variables
    USE indices
    USE model_1d
    USE pegrid
    USE profil_parameter
    USE statistics

    IMPLICIT NONE

    INTEGER ::  i, idum


    NAMELIST /inipar/  adjust_mixing_length, alpha_surface, bc_e_b, bc_lr, &
                       bc_ns, bc_p_b, bc_p_t, bc_pt_b, bc_pt_t, bc_q_b, &
             bc_q_t,bc_s_b, bc_s_t, bc_sa_t, bc_uv_b, bc_uv_t, &
             bottom_salinityflux, building_height, building_length_x, &
             building_length_y, building_wall_left, building_wall_south, &
             call_psolver_at_all_substeps, canopy_mode, canyon_height, &
             canyon_width_x, canyon_width_y, canyon_wall_left, &
             canyon_wall_south, cfl_factor, cloud_droplets, cloud_physics, &
             collective_wait, conserve_volume_flow, conserve_volume_flow_mode, &
             coupling_start_time, cthf, cut_spline_overshoot, &
             cycle_mg, damp_level_1d, dissipation_1d, & !dissipation_control, &
             dp_external, dp_level_b, dp_smooth, dpdxy, drag_coefficient, &
             dt, dt_pr_1d, dt_run_control_1d, dx, dy, dz, dz_max, & 
             dz_stretch_factor, dz_stretch_level, e_init, e_min, end_time_1d, &
             fft_method, galilei_transformation, grid_matching, humidity, &
             inflow_damping_height, inflow_damping_width, &
             inflow_disturbance_begin, inflow_disturbance_end, &
             initializing_actions, km_constant, km_damp_max, lad_surface, &
             lad_vertical_gradient, lad_vertical_gradient_level, &
             leaf_surface_concentration, long_filter_factor, &
             loop_optimization, mg_cycles, mg_switch_to_pe0_level, &
             mixing_length_1d, momentum_advec, netcdf_precision, ngsrb, nsor, &
             nsor_ini, nx, ny, nz, ocean, omega, omega_sor, &
             outflow_damping_width, overshoot_limit_e, overshoot_limit_pt, &
             overshoot_limit_u, overshoot_limit_v, overshoot_limit_w, &
             passive_scalar, pch_index, phi, plant_canopy, prandtl_layer, &
             prandtl_number, precipitation, psolver, pt_reference, pt_surface, &
             pt_surface_initial_change, pt_vertical_gradient, &
             pt_vertical_gradient_level, q_surface, q_surface_initial_change, &
             q_vertical_gradient, q_vertical_gradient_level, radiation, &
             random_generator, random_heatflux, rayleigh_damping_factor, &
             rayleigh_damping_height, recycling_width, residual_limit, &
             rif_max, rif_min, roughness_length, sa_surface, &
             sa_vertical_gradient, sa_vertical_gradient_level, scalar_advec, &
             scalar_exchange_coefficient, scalar_rayleigh_damping, &
             statistic_regions, subs_vertical_gradient, &
             subs_vertical_gradient_level, surface_heatflux, surface_pressure, &
             surface_scalarflux, surface_waterflux, s_surface, &
             s_surface_initial_change, s_vertical_gradient, &
             s_vertical_gradient_level, timestep_scheme, &
             topography, topography_grid_convention, top_heatflux, &
             top_momentumflux_u, top_momentumflux_v, top_salinityflux, &
             turbulent_inflow, ug_surface, ug_vertical_gradient, &
             ug_vertical_gradient_level, ups_limit_e, ups_limit_pt, &
             ups_limit_u, ups_limit_v, ups_limit_w, use_surface_fluxes, &
             use_top_fluxes, use_ug_for_galilei_tr, use_upstream_for_tke, &
             uv_heights, u_bulk, u_profile, vg_surface, vg_vertical_gradient, &
             vg_vertical_gradient_level, v_bulk, v_profile, wall_adjustment, &
             wall_heatflux, wall_humidityflux, wall_scalarflux


    NAMELIST /d3par/  averaging_interval, averaging_interval_pr, &
             create_disturbances, cross_normalized_x, cross_normalized_y, &
             cross_profiles, cross_ts_uymax, cross_ts_uymin, cross_xtext, &
             data_output, data_output_format, data_output_masks, &
             data_output_pr, data_output_2d_on_each_pe, disturbance_amplitude, &
             disturbance_energy_limit, disturbance_level_b, &
             disturbance_level_t, do2d_at_begin, do3d_at_begin, do3d_compress, &
             do3d_comp_prec, dt, dt_averaging_input, dt_averaging_input_pr, &
             dt_coupling, dt_data_output, dt_data_output_av, dt_disturb, &
             dt_domask, dt_dopr, dt_dopr_listing, dt_dots, dt_do2d_xy, &
             dt_do2d_xz, dt_do2d_yz, dt_do3d, dt_max, dt_restart, &
             dt_run_control,end_time, force_print_header, mask_scale_x, &
             mask_scale_y, mask_scale_z, mask_x, mask_y, mask_z, mask_x_loop, &
             mask_y_loop, mask_z_loop, netcdf_data_format, normalizing_region, &
             npex, npey, nz_do3d, precipitation_amount_interval, &
             profile_columns, profile_rows, restart_time, section_xy, &
             section_xz, section_yz, skip_time_data_output, &
             skip_time_data_output_av, skip_time_dopr, skip_time_do2d_xy, &
             skip_time_do2d_xz, skip_time_do2d_yz, skip_time_do3d, &
             skip_time_domask, synchronous_exchange, termination_time_needed, &
             use_prior_plot1d_parameters, z_max_do1d, z_max_do1d_normalized, &
             z_max_do2d


    NAMELIST /envpar/  host, local_dvrserver_running, maximum_cpu_time_allowed,&
                       maximum_parallel_io_streams, revision, return_addres, &
                       return_username, run_identifier, tasks_per_node, &
                       write_binary

!
!-- First read values of environment variables (this NAMELIST file is
!-- generated by mrun)
    OPEN ( 90, FILE='ENVPAR', STATUS='OLD', FORM='FORMATTED', ERR=30 )
    READ ( 90, envpar, ERR=31, END=32 )
    CLOSE ( 90 )

!
!-- Calculate the number of groups into which parallel I/O is split.
!-- The default for files which are opened by all PEs (or where each
!-- PE opens his own independent file) is, that all PEs are doing input/output
!-- in parallel at the same time. This might cause performance or even more
!-- severe problems depending on the configuration of the underlying file
!-- system.
!-- First, set the default:
    IF ( maximum_parallel_io_streams == -1  .OR. &
         maximum_parallel_io_streams > numprocs )  THEN
       maximum_parallel_io_streams = numprocs
    ENDIF
!
!-- Now calculate the number of io_blocks and the io_group to which the
!-- respective PE belongs. I/O of the groups is done in serial, but in parallel
!-- for all PEs belonging to the same group.
!-- These settings are repeated in init_pegrid for the communicator comm2d,
!-- which is not available here
    io_blocks = numprocs / maximum_parallel_io_streams
    io_group  = MOD( myid+1, io_blocks )

!
!-- Data is read in parallel by groups of PEs
    DO  i = 0, io_blocks-1
       IF ( i == io_group )  THEN

!
!--       Open the NAMELIST-file which is send with this job
          CALL check_open( 11 )

!
!--       Read the control parameters for initialization.
!--       The namelist "inipar" must be provided in the NAMELIST-file. If this
!--       is not the case and the file contains - instead of "inipar" - any
!--       other namelist, a read error is created on t3e and control is
!--       transferred to the statement with label 10. Therefore, on t3e
!--       machines one can not distinguish between errors produced by a wrong
!--       "inipar" namelist or because this namelist is totally missing.
           READ ( 11, inipar, ERR=10, END=11 )

#if defined ( __check )
!
!--       In case of a namelist file check, &inipar from the p3d file is
!--       used. The p3d file here must be closed and the p3df file for reading 
!--       3dpar is opened.
          IF ( check_restart == 1 ) THEN
             CALL close_file( 11 )
             check_restart = 2
             CALL check_open( 11 )             
             initializing_actions = 'read_restart_data'
          END IF
#endif
           GOTO 12

 10       message_string = 'errors in \$inipar &or no \$inipar-namelist ' // &
                           'found (CRAY-machines only)'
          CALL message( 'parin', 'PA0271', 1, 2, 0, 6, 0 )

 11       message_string = 'no \$inipar-namelist found'
          CALL message( 'parin', 'PA0272', 1, 2, 0, 6, 0 )

!
!--       If required, read control parameters from restart file (produced by
!--       a prior run). All PEs are reading from file created by PE0 (see
!--       check_open)


 12       IF ( TRIM( initializing_actions ) == 'read_restart_data' )  THEN
#if ! defined ( __check )
             CALL read_var_list
!
!--          The restart file will be reopened when reading the subdomain data
             CALL close_file( 13 )

!
!--          Increment the run count
             runnr = runnr + 1
#endif
          ENDIF

!
!--       Definition of names of areas used for computing statistics. They must
!--       be defined at this place, because they are allowed to be redefined by
!--       the user in user_parin.
          region = 'total domain'

!
!--       Read runtime parameters given by the user for this run (namelist
!--       "d3par"). The namelist "d3par" can be omitted. In that case, default
!--       values are used for the parameters.
          READ ( 11, d3par, END=20 )

!
!--       Read control parameters for optionally used model software packages
 20       CALL package_parin

!
!--       Read user-defined variables
          CALL user_parin

!
!--       Check in case of initial run, if the grid point numbers are well
!--       defined and allocate some arrays which are already needed in
!--       init_pegrid or check_parameters. During restart jobs, these arrays
!--       will be allocated in read_var_list. All other arrays are allocated
!--       in init_3d_model.
          IF ( TRIM( initializing_actions ) /= 'read_restart_data' )  THEN

             IF ( nx <= 0 )  THEN
                WRITE( message_string, * ) 'no value or wrong value given', &
                                           ' for nx: nx=', nx
                CALL message( 'parin', 'PA0273', 1, 2, 0, 6, 0 )
             ENDIF
             IF ( ny <= 0 )  THEN
                WRITE( message_string, * ) 'no value or wrong value given', &
                                           ' for ny: ny=', ny
                CALL message( 'parin', 'PA0274', 1, 2, 0, 6, 0 )
             ENDIF
             IF ( nz <= 0 )  THEN
                WRITE( message_string, * ) 'no value or wrong value given', &
                                           ' for nz: nz=', nz
                CALL message( 'parin', 'PA0275', 1, 2, 0, 6, 0 )
             ENDIF
!
!--          ATTENTION: in case of changes to the following statement please
!--                  also check the allocate statement in routine read_var_list
             ALLOCATE( lad(0:nz+1),pt_init(0:nz+1), q_init(0:nz+1),           &
                       sa_init(0:nz+1), ug(0:nz+1), u_init(0:nz+1),           &
                       v_init(0:nz+1), vg(0:nz+1),                            &
                       hom(0:nz+1,2,pr_palm+max_pr_user,0:statistic_regions), &
                       hom_sum(0:nz+1,pr_palm+max_pr_user,0:statistic_regions) )

             hom = 0.0

          ENDIF

!
!--       NAMELIST-file is not needed anymore
          CALL close_file( 11 )

       ENDIF
#if defined( __parallel ) && ! ( __check )
       CALL MPI_BARRIER( MPI_COMM_WORLD, ierr )
#endif
    ENDDO

    RETURN

 30 message_string = 'local file ENVPAR not found' // &
                     '&some variables for steering may not be properly set'
    CALL message( 'parin', 'PA0276', 0, 1, 0, 6, 0 )
    RETURN

 31 message_string = 'errors in local file ENVPAR' // &
                     '&some variables for steering may not be properly set'
    CALL message( 'parin', 'PA0277', 0, 1, 0, 6, 0 )
    RETURN

 32 message_string = 'no envpar-NAMELIST found in local file ENVPAR'  // &
                     '&some variables for steering may not be properly set'
    CALL message( 'parin', 'PA0278', 0, 1, 0, 6, 0 )

 END SUBROUTINE parin