!> @file init_grid.f90 !------------------------------------------------------------------------------! ! This file is part of the PALM model system. ! ! PALM is free software: you can redistribute it and/or modify it under the ! terms of the GNU General Public License as published by the Free Software ! Foundation, either version 3 of the License, or (at your option) any later ! version. ! ! PALM is distributed in the hope that it will be useful, but WITHOUT ANY ! WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR ! A PARTICULAR PURPOSE. See the GNU General Public License for more details. ! ! You should have received a copy of the GNU General Public License along with ! PALM. If not, see . ! ! Copyright 1997-2020 Leibniz Universitaet Hannover !------------------------------------------------------------------------------! ! ! Current revisions: ! ----------------- ! ! ! Former revisions: ! ----------------- ! $Id: init_grid.f90 4630 2020-07-30 14:54:34Z raasch $ ! In case of ASCII topography input flag grid points as terrain and building. ! ! 4601 2020-07-14 12:06:09Z suehring ! Minor formatting adjustments ! ! 4564 2020-06-12 14:03:36Z raasch ! Vertical nesting method of Huq et al. (2019) removed ! ! 4543 2020-05-20 14:12:22Z gronemeier ! Remove non-required check for canyon height ! ! 4507 2020-04-22 18:21:45Z gronemeier ! update origin_z with shifting height of orography (oro_min) ! ! 4457 2020-03-11 14:20:43Z raasch ! use statement for exchange horiz added, ! bugfix for call of exchange horiz 2d ! ! 4444 2020-03-05 15:59:50Z raasch ! bugfix: cpp-directives for serial mode added ! ! 4414 2020-02-19 20:16:04Z suehring ! - Remove deprecated topography arrays nzb_s_inner, nzb_u_inner, etc. ! - Move initialization of boundary conditions and multigrid into an extra ! module interface. ! ! 4386 2020-01-27 15:07:30Z Giersch ! Allocation statements, comments, naming of variables revised and _wp added to ! real type values ! ! 4360 2020-01-07 11:25:50Z suehring ! Revise error messages for generic tunnel setup. ! ! 4346 2019-12-18 11:55:56Z motisi ! Introduction of wall_flags_total_0, which currently sets bits based on static ! topography information used in wall_flags_static_0 ! ! 4340 2019-12-16 08:17:03Z Giersch ! Topography closed channel flow with symmetric boundaries implemented ! ! 4329 2019-12-10 15:46:36Z motisi ! Renamed wall_flags_0 to wall_flags_static_0 ! ! 4328 2019-12-09 18:53:04Z suehring ! Minor change in nzb_max computation. Commentation added. ! ! 4314 2019-11-29 10:29:20Z suehring ! Set additional topography flag 4 to mark topography grid points emerged ! from the filtering process. ! ! 4294 2019-11-13 18:34:16Z suehring ! Bugfix, always set bit 5 and 6 of wall_flags, indicating terrain- and ! building surfaces in all cases, in order to enable terrain-following output ! also when no land- or urban-surface model is applied. ! ! 4265 2019-10-15 16:16:24Z suehring ! Bugfix for last commit, exchange oro_max variable only when it is allocated ! (not necessarily the case when topography is input from ASCII file). ! ! 4245 2019-09-30 08:40:37Z pavelkrc ! Store oro_max (building z-offset) in 2D for building surfaces ! ! 4189 2019-08-26 16:19:38Z suehring ! - Add check for proper setting of namelist parameter topography ! - Set flag to indicate land surfaces in case no topography is provided ! ! 4182 2019-08-22 15:20:23Z scharf ! Corrected "Former revisions" section ! ! 4168 2019-08-16 13:50:17Z suehring ! Pre-calculate topography top index and store it on an array (replaces former ! functions get_topography_top_index) ! ! 4159 2019-08-15 13:31:35Z suehring ! Revision of topography processing. This was not consistent between 2D and 3D ! buildings. ! ! 4144 2019-08-06 09:11:47Z raasch ! relational operators .EQ., .NE., etc. replaced by ==, /=, etc. ! ! 4115 2019-07-24 12:50:49Z suehring ! Bugfix in setting near-surface flag 24, inidicating wall-bounded grid points ! ! 4110 2019-07-22 17:05:21Z suehring ! - Separate initialization of advection flags for momentum and scalars. ! - Change subroutine interface for ws_init_flags_scalar to pass boundary flags ! ! 4109 2019-07-22 17:00:34Z suehring ! Fix bad commit ! ! 3926 2019-04-23 12:56:42Z suehring ! Minor bugfix in building mapping when all building IDs in the model domain ! are missing ! ! 3857 2019-04-03 13:00:16Z knoop ! In projection of non-building 3D objects onto numerical grid remove ! dependency on building_type ! ! 3763 2019-02-25 17:33:49Z suehring ! Replace work-around for ghost point exchange of 1-byte arrays with specific ! routine as already done in other routines ! ! 3761 2019-02-25 15:31:42Z raasch ! unused variables removed ! ! 3661 2019-01-08 18:22:50Z suehring ! Remove setting of nzb_max to nzt at non-cyclic boundary PEs, instead, ! order degradation of advection scheme is handeled directly in advec_ws ! ! 3655 2019-01-07 16:51:22Z knoop ! Comment added ! ! Revision 1.1 1997/08/11 06:17:45 raasch ! Initial revision (Testversion) ! ! ! Description: ! -----------------------------------------------------------------------------! !> Creating grid depending constants !> @todo: Rearrange topo flag list !> @todo: reference 3D buildings on top of orography is not tested and may need !> further improvement for steep slopes !> @todo: Use more advanced setting of building type at filled holes !------------------------------------------------------------------------------! SUBROUTINE init_grid USE arrays_3d, & ONLY: dd2zu, ddzu, ddzu_pres, ddzw, dzu, dzw, x, xu, y, yv, zu, zw USE control_parameters, & ONLY: constant_flux_layer, dz, dz_max, dz_stretch_factor, & dz_stretch_factor_array, dz_stretch_level, dz_stretch_level_end,& dz_stretch_level_end_index, dz_stretch_level_start_index, & dz_stretch_level_start, ibc_uv_b, message_string, & number_stretch_level_end, & number_stretch_level_start, & ocean_mode, & psolver, & symmetry_flag, & topography, & use_surface_fluxes USE grid_variables, & ONLY: ddx, ddx2, ddy, ddy2, dx, dx2, dy, dy2, zu_s_inner, zw_w_inner USE indices, & ONLY: nbgp, & nx, & nxl, & nxlg, & nxr, & nxrg, & ny, & nyn, & nyng, & nys, & nysg, & nz, & nzb, & nzb_diff, & nzb_max, & nzt, & topo_top_ind, & topo_min_level USE kinds USE pegrid IMPLICIT NONE INTEGER(iwp) :: i !< index variable along x INTEGER(iwp) :: j !< index variable along y INTEGER(iwp) :: k !< index variable along z INTEGER(iwp) :: k_top !< topography top index on local PE INTEGER(iwp) :: n !< loop variable for stretching INTEGER(iwp) :: number_dz !< number of user-specified dz values INTEGER(iwp) :: nzb_local_max !< vertical grid index of maximum topography height INTEGER(iwp) :: nzb_local_min !< vertical grid index of minimum topography height INTEGER(iwp), DIMENSION(:,:,:), ALLOCATABLE :: topo !< input array for 3D topography and dummy array for setting "outer"-flags REAL(wp) :: dz_level_end !< distance between calculated height level for u/v-grid and user-specified end level for stretching REAL(wp) :: dz_stretched !< stretched vertical grid spacing REAL(wp), DIMENSION(:), ALLOCATABLE :: min_dz_stretch_level_end !< Array that contains all minimum heights where the stretching can end ! !-- Calculation of horizontal array bounds including ghost layers nxlg = nxl - nbgp nxrg = nxr + nbgp nysg = nys - nbgp nyng = nyn + nbgp ! !-- Allocate grid arrays ALLOCATE( x(0:nx) ) ALLOCATE( xu(0:nx) ) DO i = 0, nx xu(i) = i * dx x(i) = i * dx + 0.5_wp * dx ENDDO ALLOCATE( y(0:ny) ) ALLOCATE( yv(0:ny) ) DO j = 0, ny yv(j) = j * dy y(j) = j * dy + 0.5_wp * dy ENDDO ALLOCATE( ddzu(1:nzt+1) ) ALLOCATE( ddzw(1:nzt+1) ) ALLOCATE( dd2zu(1:nzt) ) ALLOCATE( dzu(1:nzt+1) ) ALLOCATE( dzw(1:nzt+1) ) ALLOCATE( zu(nzb:nzt+1) ) ALLOCATE( zw(nzb:nzt+1) ) ! !-- For constructing an appropriate grid, the vertical grid spacing dz has to !-- be specified with a non-negative value in the parameter file IF ( dz(1) == -1.0_wp ) THEN message_string = 'missing dz' CALL message( 'init_grid', 'PA0200', 1, 2, 0, 6, 0 ) ELSEIF ( dz(1) <= 0.0_wp ) THEN WRITE( message_string, * ) 'dz=',dz(1),' <= 0.0' CALL message( 'init_grid', 'PA0201', 1, 2, 0, 6, 0 ) ENDIF ! !-- Initialize dz_stretch_level_start with the value of dz_stretch_level !-- if it was set by the user IF ( dz_stretch_level /= -9999999.9_wp ) THEN dz_stretch_level_start(1) = dz_stretch_level ENDIF ! !-- Determine number of dz values and stretching levels specified by the !-- user to allow right controlling of the stretching mechanism and to !-- perform error checks. The additional requirement that dz /= dz_max !-- for counting number of user-specified dz values is necessary. Otherwise !-- restarts would abort if the old stretching mechanism with dz_stretch_level !-- is used (Attention: The user is not allowed to specify a dz value equal !-- to the default of dz_max = 999.0). number_dz = COUNT( dz /= -1.0_wp .AND. dz /= dz_max) number_stretch_level_start = COUNT( dz_stretch_level_start /= & -9999999.9_wp ) number_stretch_level_end = COUNT( dz_stretch_level_end /= & 9999999.9_wp ) ! !-- The number of specified end levels +1 has to be the same as the number !-- of specified dz values IF ( number_dz /= number_stretch_level_end + 1 ) THEN WRITE( message_string, * ) 'The number of values for dz = ', & number_dz, 'has to be the same as& ', & 'the number of values for ', & 'dz_stretch_level_end + 1 = ', & number_stretch_level_end+1 CALL message( 'init_grid', 'PA0156', 1, 2, 0, 6, 0 ) ENDIF ! !-- The number of specified start levels has to be the same or one less than !-- the number of specified dz values IF ( number_dz /= number_stretch_level_start + 1 .AND. & number_dz /= number_stretch_level_start ) THEN WRITE( message_string, * ) 'The number of values for dz = ', & number_dz, 'has to be the same as or one ', & 'more than& the number of values for ', & 'dz_stretch_level_start = ', & number_stretch_level_start CALL message( 'init_grid', 'PA0211', 1, 2, 0, 6, 0 ) ENDIF !-- The number of specified start levels has to be the same or one more than !-- the number of specified end levels IF ( number_stretch_level_start /= number_stretch_level_end + 1 .AND. & number_stretch_level_start /= number_stretch_level_end ) THEN WRITE( message_string, * ) 'The number of values for ', & 'dz_stretch_level_start = ', & dz_stretch_level_start, 'has to be the ', & 'same or one more than& the number of ', & 'values for dz_stretch_level_end = ', & number_stretch_level_end CALL message( 'init_grid', 'PA0216', 1, 2, 0, 6, 0 ) ENDIF ! !-- Initialize dz for the free atmosphere with the value of dz_max IF ( dz(number_stretch_level_start+1) == -1.0_wp .AND. & number_stretch_level_start /= 0 ) THEN dz(number_stretch_level_start+1) = dz_max ENDIF ! !-- Initialize the stretching factor if (infinitely) stretching in the free !-- atmosphere is desired (dz_stretch_level_end was not specified for the !-- free atmosphere) IF ( number_stretch_level_start == number_stretch_level_end + 1 ) THEN dz_stretch_factor_array(number_stretch_level_start) = & dz_stretch_factor ENDIF ! !-- Allocation of arrays for stretching ALLOCATE( min_dz_stretch_level_end(number_stretch_level_start) ) ! !-- Define the vertical grid levels. Start with atmosphere branch IF ( .NOT. ocean_mode ) THEN ! !-- The stretching region has to be large enough to allow for a smooth !-- transition between two different grid spacings. The number 4 is an !-- empirical value DO n = 1, number_stretch_level_start min_dz_stretch_level_end(n) = dz_stretch_level_start(n) + & 4 * MAX( dz(n),dz(n+1) ) ENDDO IF ( ANY( min_dz_stretch_level_end(1:number_stretch_level_start) > & dz_stretch_level_end(1:number_stretch_level_start) ) ) THEN message_string= 'Each dz_stretch_level_end has to be larger ' // & 'than its corresponding value for &' // & 'dz_stretch_level_start + 4*MAX(dz(n),dz(n+1)) '// & 'to allow for smooth grid stretching' CALL message( 'init_grid', 'PA0224', 1, 2, 0, 6, 0 ) ENDIF ! !-- Stretching must not be applied within the surface layer !-- (first two grid points). For the default case dz_stretch_level_start !-- is negative. Therefore the absolut value is checked here. IF ( ANY( ABS( dz_stretch_level_start ) <= dz(1) * 1.5_wp ) ) THEN WRITE( message_string, * ) 'Each dz_stretch_level_start has to be ',& 'larger than ', dz(1) * 1.5 CALL message( 'init_grid', 'PA0226', 1, 2, 0, 6, 0 ) ENDIF ! !-- The stretching has to start and end on a grid level. Therefore !-- user-specified values are mapped to the next lowest level. The !-- calculation of the first level is realized differently just because of !-- historical reasons (the advanced/new stretching mechanism was realized !-- in a way that results don't change if the old parameters !-- dz_stretch_level, dz_stretch_factor and dz_max are used) IF ( number_stretch_level_start /= 0 ) THEN dz_stretch_level_start(1) = INT( (dz_stretch_level_start(1) - & dz(1)/2.0) / dz(1) ) & * dz(1) + dz(1)/2.0 ENDIF IF ( number_stretch_level_start > 1 ) THEN DO n = 2, number_stretch_level_start dz_stretch_level_start(n) = INT( dz_stretch_level_start(n) / & dz(n) ) * dz(n) ENDDO ENDIF IF ( number_stretch_level_end /= 0 ) THEN DO n = 1, number_stretch_level_end dz_stretch_level_end(n) = INT( dz_stretch_level_end(n) / & dz(n+1) ) * dz(n+1) ENDDO ENDIF ! !-- Determine stretching factor if necessary IF ( number_stretch_level_end >= 1 ) THEN CALL calculate_stretching_factor( number_stretch_level_end ) ENDIF ! !-- Grid for atmosphere with surface at z=0 (k=0, w-grid). !-- First compute the u- and v-levels. In case of dirichlet bc for u and v !-- the first u/v- and w-level (k=0) are defined at same height (z=0). !-- The second u-level (k=1) corresponds to the top of the !-- surface layer. In case of symmetric boundaries (closed channel flow), !-- the first grid point is always at z=0. IF ( ibc_uv_b == 0 .OR. ibc_uv_b == 2 .OR. & topography == 'closed_channel' ) THEN zu(0) = 0.0_wp ELSE zu(0) = - dz(1) * 0.5_wp ENDIF zu(1) = dz(1) * 0.5_wp ! !-- Determine u and v height levels considering the possibility of grid !-- stretching in several heights. n = 1 dz_stretch_level_start_index = nzt+1 dz_stretch_level_end_index = nzt+1 dz_stretched = dz(1) !-- The default value of dz_stretch_level_start is negative, thus the first !-- condition is true even if no stretching shall be applied. Hence, the !-- second condition is also necessary. DO k = 2, nzt+1-symmetry_flag IF ( dz_stretch_level_start(n) <= zu(k-1) .AND. & dz_stretch_level_start(n) /= -9999999.9_wp ) THEN dz_stretched = dz_stretched * dz_stretch_factor_array(n) IF ( dz(n) > dz(n+1) ) THEN dz_stretched = MAX( dz_stretched, dz(n+1) ) !Restrict dz_stretched to the user-specified (higher) dz ELSE dz_stretched = MIN( dz_stretched, dz(n+1) ) !Restrict dz_stretched to the user-specified (lower) dz ENDIF IF ( dz_stretch_level_start_index(n) == nzt+1 ) & dz_stretch_level_start_index(n) = k-1 ENDIF zu(k) = zu(k-1) + dz_stretched ! !-- Make sure that the stretching ends exactly at dz_stretch_level_end dz_level_end = ABS( zu(k) - dz_stretch_level_end(n) ) IF ( dz_level_end < dz(n+1)/3.0 ) THEN zu(k) = dz_stretch_level_end(n) dz_stretched = dz(n+1) dz_stretch_level_end_index(n) = k n = n + 1 ENDIF ENDDO ! !-- If a closed channel flow is simulated, make sure that grid structure is !-- the same for both bottom and top boundary. (Hint: Using a different dz !-- at the bottom and at the top makes no sense due to symmetric boundaries !-- where dz should be equal. Therefore, different dz at the bottom and top !-- causes an abort (see check_parameters).) IF ( topography == 'closed_channel' ) THEN zu(nzt+1) = zu(nzt) + dz(1) * 0.5_wp ENDIF ! !-- Compute the w-levels. They are always staggered half-way between the !-- corresponding u-levels. In case of dirichlet bc for u and v at the !-- ground the first u- and w-level (k=0) are defined at same height (z=0). !-- Per default, the top w-level is extrapolated linearly. In case of !-- a closed channel flow, zu(nzt+1) and zw(nzt) must be set explicitely. !-- (Hint: Using a different dz at the bottom and at the top makes no sense !-- due to symmetric boundaries where dz should be equal. Therefore, !-- different dz at the bottom and top causes an abort (see !-- check_parameters).) zw(0) = 0.0_wp DO k = 1, nzt-symmetry_flag zw(k) = ( zu(k) + zu(k+1) ) * 0.5_wp ENDDO IF ( topography == 'closed_channel' ) THEN zw(nzt) = zw(nzt-1) + dz(1) zw(nzt+1) = zw(nzt) + dz(1) ELSE zw(nzt+1) = zw(nzt) + 2.0_wp * ( zu(nzt+1) - zw(nzt) ) ENDIF ELSE !ocean branch ! !-- The stretching region has to be large enough to allow for a smooth !-- transition between two different grid spacings. The number 4 is an !-- empirical value DO n = 1, number_stretch_level_start min_dz_stretch_level_end(n) = dz_stretch_level_start(n) - & 4 * MAX( dz(n),dz(n+1) ) ENDDO IF ( ANY( min_dz_stretch_level_end (1:number_stretch_level_start) < & dz_stretch_level_end(1:number_stretch_level_start) ) ) THEN message_string= 'Each dz_stretch_level_end has to be less ' // & 'than its corresponding value for &' // & 'dz_stretch_level_start - 4*MAX(dz(n),dz(n+1)) '//& 'to allow for smooth grid stretching' CALL message( 'init_grid', 'PA0224', 1, 2, 0, 6, 0 ) ENDIF ! !-- Stretching must not be applied close to the surface (last two grid !-- points). For the default case dz_stretch_level_start is negative. IF ( ANY( dz_stretch_level_start >= - dz(1) * 1.5_wp ) ) THEN WRITE( message_string, * ) 'Each dz_stretch_level_start has to be ',& 'less than ', -dz(1) * 1.5 CALL message( 'init_grid', 'PA0226', 1, 2, 0, 6, 0 ) ENDIF ! !-- The stretching has to start and end on a grid level. Therefore !-- user-specified values are mapped to the next highest level. The !-- calculation of the first level is realized differently just because of !-- historical reasons (the advanced/new stretching mechanism was realized !-- in a way that results don't change if the old parameters !-- dz_stretch_level, dz_stretch_factor and dz_max are used) IF ( number_stretch_level_start /= 0 ) THEN dz_stretch_level_start(1) = INT( (dz_stretch_level_start(1) + & dz(1)/2.0) / dz(1) ) & * dz(1) - dz(1)/2.0 ENDIF IF ( number_stretch_level_start > 1 ) THEN DO n = 2, number_stretch_level_start dz_stretch_level_start(n) = INT( dz_stretch_level_start(n) / & dz(n) ) * dz(n) ENDDO ENDIF IF ( number_stretch_level_end /= 0 ) THEN DO n = 1, number_stretch_level_end dz_stretch_level_end(n) = INT( dz_stretch_level_end(n) / & dz(n+1) ) * dz(n+1) ENDDO ENDIF ! !-- Determine stretching factor if necessary IF ( number_stretch_level_end >= 1 ) THEN CALL calculate_stretching_factor( number_stretch_level_end ) ENDIF ! !-- Grid for ocean with free water surface is at k=nzt (w-grid). !-- In case of neumann bc at the ground the first first u-level (k=0) lies !-- below the first w-level (k=0). In case of dirichlet bc the first u- and !-- w-level are defined at same height, but staggered from the second level. !-- The second u-level (k=1) corresponds to the top of the surface layer. !-- z values are negative starting from z=0 (surface) zu(nzt+1) = dz(1) * 0.5_wp zu(nzt) = - dz(1) * 0.5_wp ! !-- Determine u and v height levels considering the possibility of grid !-- stretching in several heights. n = 1 dz_stretch_level_start_index = 0 dz_stretch_level_end_index = 0 dz_stretched = dz(1) DO k = nzt-1, 0, -1 IF ( dz_stretch_level_start(n) >= zu(k+1) ) THEN dz_stretched = dz_stretched * dz_stretch_factor_array(n) IF ( dz(n) > dz(n+1) ) THEN dz_stretched = MAX( dz_stretched, dz(n+1) ) !Restrict dz_stretched to the user-specified (higher) dz ELSE dz_stretched = MIN( dz_stretched, dz(n+1) ) !Restrict dz_stretched to the user-specified (lower) dz ENDIF IF ( dz_stretch_level_start_index(n) == 0 ) & dz_stretch_level_start_index(n) = k+1 ENDIF zu(k) = zu(k+1) - dz_stretched ! !-- Make sure that the stretching ends exactly at dz_stretch_level_end dz_level_end = ABS( zu(k) - dz_stretch_level_end(n) ) IF ( dz_level_end < dz(n+1)/3.0 ) THEN zu(k) = dz_stretch_level_end(n) dz_stretched = dz(n+1) dz_stretch_level_end_index(n) = k n = n + 1 ENDIF ENDDO ! !-- Compute the w-levels. They are always staggered half-way between the !-- corresponding u-levels, except in case of dirichlet bc for u and v !-- at the ground. In this case the first u- and w-level are defined at !-- same height. The top w-level (nzt+1) is not used but set for !-- consistency, since w and all scalar variables are defined up tp nzt+1. zw(nzt+1) = dz(1) zw(nzt) = 0.0_wp DO k = 0, nzt zw(k) = ( zu(k) + zu(k+1) ) * 0.5_wp ENDDO ! !-- In case of dirichlet bc for u and v the first u- and w-level are defined !-- at same height. IF ( ibc_uv_b == 0 ) THEN zu(0) = zw(0) ENDIF ENDIF !End of defining the vertical grid levels ! !-- Compute grid lengths. DO k = 1, nzt+1 dzu(k) = zu(k) - zu(k-1) ddzu(k) = 1.0_wp / dzu(k) dzw(k) = zw(k) - zw(k-1) ddzw(k) = 1.0_wp / dzw(k) ENDDO DO k = 1, nzt dd2zu(k) = 1.0_wp / ( dzu(k) + dzu(k+1) ) ENDDO ! !-- The FFT- SOR-pressure solvers assume grid spacings of a staggered grid !-- everywhere. For the actual grid, the grid spacing at the lowest level !-- is only dz/2, but should be dz. Therefore, an additional array !-- containing with appropriate grid information is created for these !-- solvers. IF ( psolver(1:9) /= 'multigrid' ) THEN ALLOCATE( ddzu_pres(1:nzt+1) ) ddzu_pres = ddzu ddzu_pres(1) = ddzu_pres(2) ! change for lowest level ENDIF ! !-- Compute the reciprocal values of the horizontal grid lengths. ddx = 1.0_wp / dx ddy = 1.0_wp / dy dx2 = dx * dx dy2 = dy * dy ddx2 = 1.0_wp / dx2 ddy2 = 1.0_wp / dy2 ! !-- Allocate 3D array to set topography ALLOCATE( topo(nzb:nzt+1,nysg:nyng,nxlg:nxrg) ) topo = 0 ! !-- Initialize topography by generic topography or read topography from file. CALL init_topo( topo ) ! !-- Set flags to mask topography on the grid. CALL set_topo_flags( topo ) ! !-- Determine the maximum level of topography. It is used for !-- steering the degradation of order of the applied advection scheme, !-- as well in the lpm. k_top = 0 DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt + 1 k_top = MAX( k_top, MERGE( k, 0, .NOT. BTEST( topo(k,j,i), 0 ) ) ) ENDDO ENDDO ENDDO #if defined( __parallel ) CALL MPI_ALLREDUCE( k_top, nzb_max, 1, MPI_INTEGER, & MPI_MAX, comm2d, ierr ) #else nzb_max = k_top #endif ! !-- Increment nzb_max by 1 in order to allow for proper diverengence correction. !-- Further, in case topography extents up to the model top, limit to nzt. nzb_max = MIN( nzb_max+1, nzt ) ! !-- Determine minimum index of topography. Usually, this will be nzb. In case !-- there is elevated topography, however, the lowest topography will be higher. !-- This index is e.g. used to calculate mean first-grid point atmosphere !-- temperature, surface pressure and density, etc. . topo_min_level = 0 #if defined( __parallel ) CALL MPI_ALLREDUCE( MINVAL( topo_top_ind(nys:nyn,nxl:nxr,0) ), & topo_min_level, 1, MPI_INTEGER, MPI_MIN, comm2d, ierr ) #else topo_min_level = MINVAL( topo_top_ind(nys:nyn,nxl:nxr,0) ) #endif ! !-- Check topography for consistency with model domain. Therefore, use !-- maximum and minium topography-top indices. Note, minimum topography top !-- index is already calculated. IF ( TRIM( topography ) /= 'flat' ) THEN #if defined( __parallel ) CALL MPI_ALLREDUCE( MAXVAL( topo_top_ind(nys:nyn,nxl:nxr,0) ), & nzb_local_max, 1, MPI_INTEGER, MPI_MAX, comm2d, ierr ) #else nzb_local_max = MAXVAL( topo_top_ind(nys:nyn,nxl:nxr,0) ) #endif nzb_local_min = topo_min_level ! !-- Consistency checks IF ( nzb_local_min < 0 .OR. nzb_local_max > nz + 1 ) THEN WRITE( message_string, * ) 'nzb_local values are outside the', & ' model domain', & '&MINVAL( nzb_local ) = ', nzb_local_min, & '&MAXVAL( nzb_local ) = ', nzb_local_max CALL message( 'init_grid', 'PA0210', 1, 2, 0, 6, 0 ) ENDIF ENDIF ! !-- Define vertical gridpoint from (or to) which on the usual finite difference !-- form (which does not use surface fluxes) is applied IF ( constant_flux_layer .OR. use_surface_fluxes ) THEN nzb_diff = nzb + 2 ELSE nzb_diff = nzb + 1 ENDIF IF ( TRIM( topography ) /= 'flat' ) THEN ! !-- Allocate and set the arrays containing the topography height (for output !-- reasons only). IF ( nxr == nx .AND. nyn /= ny ) THEN ALLOCATE( zu_s_inner(nxl:nxr+1,nys:nyn), & zw_w_inner(nxl:nxr+1,nys:nyn) ) ELSEIF ( nxr /= nx .AND. nyn == ny ) THEN ALLOCATE( zu_s_inner(nxl:nxr,nys:nyn+1), & zw_w_inner(nxl:nxr,nys:nyn+1) ) ELSEIF ( nxr == nx .AND. nyn == ny ) THEN ALLOCATE( zu_s_inner(nxl:nxr+1,nys:nyn+1), & zw_w_inner(nxl:nxr+1,nys:nyn+1) ) ELSE ALLOCATE( zu_s_inner(nxl:nxr,nys:nyn), & zw_w_inner(nxl:nxr,nys:nyn) ) ENDIF zu_s_inner = 0.0_wp zw_w_inner = 0.0_wp ! !-- Determine local topography height on scalar and w-grid. Note, setting !-- lateral boundary values is not necessary, realized via wall_flags_static_0 !-- array. Further, please note that loop bounds are different from !-- nxl to nxr and nys to nyn on south and right model boundary, hence, !-- use intrinsic lbound and ubound functions to infer array bounds. DO i = LBOUND(zu_s_inner, 1), UBOUND(zu_s_inner, 1) DO j = LBOUND(zu_s_inner, 2), UBOUND(zu_s_inner, 2) ! !-- Topography height on scalar grid. Therefore, determine index of !-- upward-facing surface element on scalar grid. zu_s_inner(i,j) = zu(topo_top_ind(j,i,0)) ! !-- Topography height on w grid. Therefore, determine index of !-- upward-facing surface element on w grid. zw_w_inner(i,j) = zw(topo_top_ind(j,i,3)) ENDDO ENDDO ENDIF END SUBROUTINE init_grid ! Description: ! -----------------------------------------------------------------------------! !> Calculation of the stretching factor through an iterative method. Ideas were !> taken from the paper "Regional stretched grid generation and its application !> to the NCAR RegCM (1999)". Normally, no analytic solution exists because the !> system of equations has two variables (r,l) but four requirements !> (l=integer, r=[0,88;1,2], Eq(6), Eq(5) starting from index j=1) which !> results into an overdetermined system. !------------------------------------------------------------------------------! SUBROUTINE calculate_stretching_factor( number_end ) USE control_parameters, & ONLY: dz, dz_stretch_factor_array, & dz_stretch_level_end, dz_stretch_level_start, message_string USE kinds IMPLICIT NONE INTEGER(iwp) :: iterations !< number of iterations until stretch_factor_lower/upper_limit is reached INTEGER(iwp) :: l_rounded !< after l_rounded grid levels dz(n) is strechted to dz(n+1) with stretch_factor_2 INTEGER(iwp) :: n !< loop variable for stretching INTEGER(iwp), INTENT(IN) :: number_end !< number of user-specified end levels for stretching REAL(wp) :: delta_l !< absolute difference between l and l_rounded REAL(wp) :: delta_stretch_factor !< absolute difference between stretch_factor_1 and stretch_factor_2 REAL(wp) :: delta_total_new !< sum of delta_l and delta_stretch_factor for the next iteration (should be as small as possible) REAL(wp) :: delta_total_old !< sum of delta_l and delta_stretch_factor for the last iteration REAL(wp) :: distance !< distance between dz_stretch_level_start and dz_stretch_level_end (stretching region) REAL(wp) :: l !< value that fulfil Eq. (5) in the paper mentioned above together with stretch_factor_1 exactly REAL(wp) :: numerator !< numerator of the quotient REAL(wp) :: stretch_factor_1 !< stretching factor that fulfil Eq. (5) togehter with l exactly REAL(wp) :: stretch_factor_2 !< stretching factor that fulfil Eq. (6) togehter with l_rounded exactly REAL(wp) :: dz_stretch_factor_array_2(9) = 1.08_wp !< Array that contains all stretch_factor_2 that belongs to stretch_factor_1 REAL(wp), PARAMETER :: stretch_factor_interval = 1.0E-06_wp !< interval for sampling possible stretching factors REAL(wp), PARAMETER :: stretch_factor_lower_limit = 0.88_wp !< lowest possible stretching factor REAL(wp), PARAMETER :: stretch_factor_upper_limit = 1.12_wp !< highest possible stretching factor l = 0 DO n = 1, number_end iterations = 1 stretch_factor_1 = 1.0_wp stretch_factor_2 = 1.0_wp delta_total_old = 1.0_wp ! !-- First branch for stretching from rough to fine IF ( dz(n) > dz(n+1) ) THEN DO WHILE ( stretch_factor_1 >= stretch_factor_lower_limit ) stretch_factor_1 = 1.0_wp - iterations * stretch_factor_interval distance = ABS( dz_stretch_level_end(n) - & dz_stretch_level_start(n) ) numerator = distance*stretch_factor_1/dz(n) + & stretch_factor_1 - distance/dz(n) IF ( numerator > 0.0_wp ) THEN l = LOG( numerator ) / LOG( stretch_factor_1 ) - 1.0_wp l_rounded = NINT( l ) delta_l = ABS( l_rounded - l ) / l ENDIF stretch_factor_2 = EXP( LOG( dz(n+1)/dz(n) ) / (l_rounded) ) delta_stretch_factor = ABS( stretch_factor_1 - & stretch_factor_2 ) / & stretch_factor_2 delta_total_new = delta_l + delta_stretch_factor ! !-- stretch_factor_1 is taken to guarantee that the stretching !-- procedure ends as close as possible to dz_stretch_level_end. !-- stretch_factor_2 would guarantee that the stretched dz(n) is !-- equal to dz(n+1) after l_rounded grid levels. IF (delta_total_new < delta_total_old) THEN dz_stretch_factor_array(n) = stretch_factor_1 dz_stretch_factor_array_2(n) = stretch_factor_2 delta_total_old = delta_total_new ENDIF iterations = iterations + 1 ENDDO ! !-- Second branch for stretching from fine to rough ELSEIF ( dz(n) < dz(n+1) ) THEN DO WHILE ( stretch_factor_1 <= stretch_factor_upper_limit ) stretch_factor_1 = 1.0_wp + iterations * stretch_factor_interval distance = ABS( dz_stretch_level_end(n) - & dz_stretch_level_start(n) ) numerator = distance*stretch_factor_1/dz(n) + & stretch_factor_1 - distance/dz(n) l = LOG( numerator ) / LOG( stretch_factor_1 ) - 1.0_wp l_rounded = NINT( l ) delta_l = ABS( l_rounded - l ) / l stretch_factor_2 = EXP( LOG( dz(n+1)/dz(n) ) / (l_rounded) ) delta_stretch_factor = ABS( stretch_factor_1 - & stretch_factor_2 ) / & stretch_factor_2 delta_total_new = delta_l + delta_stretch_factor ! !-- stretch_factor_1 is taken to guarantee that the stretching !-- procedure ends as close as possible to dz_stretch_level_end. !-- stretch_factor_2 would guarantee that the stretched dz(n) is !-- equal to dz(n+1) after l_rounded grid levels. IF (delta_total_new < delta_total_old) THEN dz_stretch_factor_array(n) = stretch_factor_1 dz_stretch_factor_array_2(n) = stretch_factor_2 delta_total_old = delta_total_new ENDIF iterations = iterations + 1 ENDDO ELSE message_string= 'Two adjacent values of dz must be different' CALL message( 'init_grid', 'PA0228', 1, 2, 0, 6, 0 ) ENDIF ! !-- Check if also the second stretching factor fits into the allowed !-- interval. If not, print a warning for the user. IF ( dz_stretch_factor_array_2(n) < stretch_factor_lower_limit .OR. & dz_stretch_factor_array_2(n) > stretch_factor_upper_limit ) THEN WRITE( message_string, * ) 'stretch_factor_2 = ', & dz_stretch_factor_array_2(n), ' which is',& ' responsible for exactly reaching& dz =',& dz(n+1), 'after a specific amount of', & ' grid levels& exceeds the upper', & ' limit =', stretch_factor_upper_limit, & ' &or lower limit = ', & stretch_factor_lower_limit CALL message( 'init_grid', 'PA0499', 0, 1, 0, 6, 0 ) ENDIF ENDDO END SUBROUTINE calculate_stretching_factor ! Description: ! -----------------------------------------------------------------------------! !> Set temporary topography flags and reference buildings on top of underlying !> orography. !------------------------------------------------------------------------------! SUBROUTINE process_topography( topo_3d ) USE arrays_3d, & ONLY: zu, zw USE control_parameters, & ONLY: bc_lr_cyc, bc_ns_cyc, ocean_mode USE exchange_horiz_mod, & ONLY: exchange_horiz_int, exchange_horiz_2d USE indices, & ONLY: nbgp, nx, nxl, nxlg, nxr, nxrg, ny, nyn, nyng, nys, nysg, nzb, & nzt USE netcdf_data_input_mod, & ONLY: buildings_f, building_id_f, building_type_f, & init_model, & input_pids_static, & terrain_height_f USE kinds USE pegrid IMPLICIT NONE INTEGER(iwp) :: i !< running index along x-direction INTEGER(iwp) :: j !< running index along y-direction INTEGER(iwp) :: k !< running index along z-direction with respect to numeric grid INTEGER(iwp) :: k2 !< running index along z-direction with respect to netcdf grid INTEGER(iwp) :: nr !< index variable indication maximum terrain height for respective building ID INTEGER(iwp) :: num_build !< counter for number of buildings INTEGER(iwp) :: topo_top_index !< orography top index, used to map 3D buildings onto terrain #if defined( __parallel ) INTEGER(iwp), DIMENSION(:), ALLOCATABLE :: displace_dum !< displacements of start addresses, used for MPI_ALLGATHERV #endif INTEGER(iwp), DIMENSION(:), ALLOCATABLE :: build_ids !< building IDs on entire model domain INTEGER(iwp), DIMENSION(:), ALLOCATABLE :: build_ids_final !< building IDs on entire model domain, multiple occurences are sorted out INTEGER(iwp), DIMENSION(:), ALLOCATABLE :: build_ids_final_tmp !< temporary array used for resizing INTEGER(iwp), DIMENSION(:), ALLOCATABLE :: build_ids_l !< building IDs on local subdomain INTEGER(iwp), DIMENSION(:), ALLOCATABLE :: build_ids_l_tmp !< temporary array used to resize array of building IDs INTEGER(iwp), DIMENSION(0:numprocs-1) :: num_buildings !< number of buildings with different ID on entire model domain INTEGER(iwp), DIMENSION(0:numprocs-1) :: num_buildings_l !< number of buildings with different ID on local subdomain INTEGER(iwp), DIMENSION(nzb:nzt+1,nysg:nyng,nxlg:nxrg) :: topo_3d !< input array for 3D topography and dummy array for setting "outer"-flags REAL(wp) :: ocean_offset !< offset to consider inverse vertical coordinate at topography definition REAL(wp) :: oro_min = 0.0_wp !< minimum terrain height in entire model domain, used to reference terrain to zero REAL(wp), DIMENSION(:), ALLOCATABLE :: oro_max !< maximum terrain height occupied by an building with certain id REAL(wp), DIMENSION(:), ALLOCATABLE :: oro_max_l !< maximum terrain height occupied by an building with certain id, on local subdomain ! !-- Reference lowest terrain height to zero. This ensures that first, !-- non-required gird levels (those which lie entirely below the minimum !-- orography) are avoided, and second, that also negative orography can be used !-- within the input file. !-- Please note, in case of a nested run, the global minimum from all parent and !-- childs need to be remove to avoid steep edges at the child-domain boundaries. IF ( input_pids_static ) THEN #if defined( __parallel ) CALL MPI_ALLREDUCE( MINVAL( terrain_height_f%var ), oro_min, 1, & MPI_REAL, MPI_MIN, MPI_COMM_WORLD, ierr ) #else oro_min = MINVAL( terrain_height_f%var ) #endif terrain_height_f%var = terrain_height_f%var - oro_min ! !-- Update reference height used within output files init_model%origin_z = init_model%origin_z + oro_min ENDIF ! !-- In the following, buildings and orography are further preprocessed !-- before they are mapped on the LES grid. !-- Buildings are mapped on top of the orography by maintaining the roof !-- shape of the building. This can be achieved by referencing building on !-- top of the maximum terrain height within the area occupied by the !-- respective building. As buildings and terrain height are defined PE-wise, !-- parallelization of this referencing is required (a building can be !-- distributed between different PEs). !-- In a first step, determine the number of buildings with different !-- building id on each PE. In a next step, all building ids are gathered !-- into one array which is present to all PEs. For each building ID, !-- the maximum terrain height occupied by the respective building is !-- computed and distributed to each PE. !-- Finally, for each building id and its respective reference orography, !-- builidings are mapped on top. !-- !-- First, pre-set topography flags, bit 1 indicates orography, bit 2 !-- buildings !-- classify the respective surfaces. topo_3d = IBSET( topo_3d, 0 ) topo_3d(nzb,:,:) = IBCLR( topo_3d(nzb,:,:), 0 ) ! !-- In order to map topography on PALM grid also in case of ocean simulations, !-- pre-calculate an offset value. ocean_offset = MERGE( zw(0), 0.0_wp, ocean_mode ) ! !-- Reference buildings on top of orography. This is not necessary !-- if topography is read from ASCII file as no distinction between buildings !-- and terrain height can be made. Moreover, this is also not necessary if !-- urban-surface and land-surface model are used at the same time. IF ( input_pids_static ) THEN IF ( buildings_f%from_file ) THEN num_buildings_l = 0 num_buildings = 0 ! !-- Allocate at least one element for building ids and give it an inital !-- negative value that will be overwritten later. This, however, is !-- necessary in case there all IDs in the model domain are fill values. ALLOCATE( build_ids_l(1) ) build_ids_l = -1 DO i = nxl, nxr DO j = nys, nyn IF ( building_id_f%var(j,i) /= building_id_f%fill ) THEN IF ( num_buildings_l(myid) > 0 ) THEN IF ( ANY( building_id_f%var(j,i) == build_ids_l ) ) & THEN CYCLE ELSE num_buildings_l(myid) = num_buildings_l(myid) + 1 ! !-- Resize array with different local building ids ALLOCATE( build_ids_l_tmp(1:SIZE(build_ids_l)) ) build_ids_l_tmp = build_ids_l DEALLOCATE( build_ids_l ) ALLOCATE( build_ids_l(1:num_buildings_l(myid)) ) build_ids_l(1:num_buildings_l(myid)-1) = & build_ids_l_tmp(1:num_buildings_l(myid)-1) build_ids_l(num_buildings_l(myid)) = building_id_f%var(j,i) DEALLOCATE( build_ids_l_tmp ) ENDIF ! !-- First occuring building id on PE ELSE num_buildings_l(myid) = num_buildings_l(myid) + 1 build_ids_l(1) = building_id_f%var(j,i) ENDIF ENDIF ENDDO ENDDO ! !-- Determine number of different building ids for the entire domain #if defined( __parallel ) CALL MPI_ALLREDUCE( num_buildings_l, num_buildings, numprocs, & MPI_INTEGER, MPI_SUM, comm2d, ierr ) #else num_buildings = num_buildings_l #endif ! !-- Gather all buildings ids on each PEs. !-- First, allocate array encompassing all building ids in model domain. ALLOCATE( build_ids(1:SUM(num_buildings)) ) #if defined( __parallel ) ! !-- Allocate array for displacements. !-- As each PE may has a different number of buildings, so that !-- the block sizes send by each PE may not be equal. Hence, !-- information about the respective displacement is required, indicating !-- the respective adress where each MPI-task writes into the receive !-- buffer array ALLOCATE( displace_dum(0:numprocs-1) ) displace_dum(0) = 0 DO i = 1, numprocs-1 displace_dum(i) = displace_dum(i-1) + num_buildings(i-1) ENDDO CALL MPI_ALLGATHERV( build_ids_l(1:num_buildings_l(myid)), & num_buildings(myid), & MPI_INTEGER, & build_ids, & num_buildings, & displace_dum, & MPI_INTEGER, & comm2d, ierr ) DEALLOCATE( displace_dum ) #else build_ids = build_ids_l #endif ! !-- Note, in parallel mode building ids can occure mutliple times, as !-- each PE has send its own ids. Therefore, sort out building ids which !-- appear more than one time. num_build = 0 DO nr = 1, SIZE(build_ids) IF ( ALLOCATED(build_ids_final) ) THEN IF ( ANY( build_ids(nr) == build_ids_final ) ) THEN CYCLE ELSE num_build = num_build + 1 ! !-- Resize ALLOCATE( build_ids_final_tmp(1:num_build) ) build_ids_final_tmp(1:num_build-1) = build_ids_final(1:num_build-1) DEALLOCATE( build_ids_final ) ALLOCATE( build_ids_final(1:num_build) ) build_ids_final(1:num_build-1) = build_ids_final_tmp(1:num_build-1) build_ids_final(num_build) = build_ids(nr) DEALLOCATE( build_ids_final_tmp ) ENDIF ELSE num_build = num_build + 1 ALLOCATE( build_ids_final(1:num_build) ) build_ids_final(num_build) = build_ids(nr) ENDIF ENDDO ! !-- Determine maximumum terrain height occupied by the respective !-- building and temporalily store on oro_max ALLOCATE( oro_max_l(1:SIZE(build_ids_final)) ) ALLOCATE( oro_max(1:SIZE(build_ids_final)) ) oro_max_l = 0.0_wp DO nr = 1, SIZE(build_ids_final) oro_max_l(nr) = MAXVAL( & MERGE( terrain_height_f%var(nys:nyn,nxl:nxr), & 0.0_wp, & building_id_f%var(nys:nyn,nxl:nxr) == & build_ids_final(nr) ) ) ENDDO #if defined( __parallel ) IF ( SIZE(build_ids_final) >= 1 ) THEN CALL MPI_ALLREDUCE( oro_max_l, oro_max, SIZE( oro_max ), MPI_REAL,& MPI_MAX, comm2d, ierr ) ENDIF #else oro_max = oro_max_l #endif ! !-- Finally, determine discrete grid height of maximum orography occupied !-- by a building. Use all-or-nothing approach, i.e. if terrain !-- exceeds the scalar level the grid box is fully terrain and the !-- maximum terrain is set to the zw level. !-- terrain or oro_max_l = 0.0 DO nr = 1, SIZE(build_ids_final) DO k = nzb, nzt IF ( zu(k) - ocean_offset <= oro_max(nr) ) & oro_max_l(nr) = zw(k) - ocean_offset ENDDO oro_max(nr) = oro_max_l(nr) ENDDO ENDIF ! !-- Allocate array for storing terrain height under buildings IF ( buildings_f%from_file ) THEN ALLOCATE( buildings_f%oro_max(nysg:nyng,nxlg:nxrg) ) buildings_f%oro_max = buildings_f%fill1 END IF ! !-- Map orography as well as buildings onto grid. DO i = nxl, nxr DO j = nys, nyn topo_top_index = 0 ! !-- Obtain index in global building_id array IF ( buildings_f%from_file ) THEN IF ( building_id_f%var(j,i) /= building_id_f%fill ) THEN ! !-- Determine index where maximum terrain height occupied by !-- the respective building height is stored. nr = MINLOC( ABS( build_ids_final - & building_id_f%var(j,i) ), DIM = 1 ) ! !-- Save grid-indexed oro_max buildings_f%oro_max(j,i) = oro_max(nr) ENDIF ENDIF DO k = nzb, nzt ! !-- In a first step, if grid point is below or equal the given !-- terrain height, grid point is flagged to be of type natural. !-- Please note, in case there is also a building which is lower !-- than the vertical grid spacing, initialization of surface !-- attributes will not be correct as given surface information !-- will not be in accordance to the classified grid points. !-- Hence, in this case, also a building flag. IF ( zu(k) - ocean_offset <= terrain_height_f%var(j,i) ) THEN topo_3d(k,j,i) = IBCLR( topo_3d(k,j,i), 0 ) topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 1 ) topo_top_index = k ! topo_top_index + 1 ENDIF ! !-- Set building grid points. Here, only consider 2D buildings. !-- 3D buildings require separate treatment. IF ( buildings_f%from_file .AND. buildings_f%lod == 1 ) THEN ! !-- Fill-up the terrain to the level of maximum orography !-- within the building-covered area. IF ( building_id_f%var(j,i) /= building_id_f%fill ) THEN ! !-- Note, oro_max is always on zw level IF ( zu(k) - ocean_offset < oro_max(nr) ) THEN topo_3d(k,j,i) = IBCLR( topo_3d(k,j,i), 0 ) topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 1 ) ELSEIF ( zu(k) - ocean_offset <= & oro_max(nr) + buildings_f%var_2d(j,i) ) THEN topo_3d(k,j,i) = IBCLR( topo_3d(k,j,i), 0 ) topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 2 ) ENDIF ENDIF ENDIF ENDDO ! !-- Special treatment for non grid-resolved buildings. This case, !-- the uppermost terrain grid point is flagged as building as well !-- well, even though no building exists at all. However, the !-- surface element will be identified as urban-surface and the !-- input data provided by the drivers is consistent to the surface !-- classification. Else, all non grid-resolved buildings would vanish !-- and identified as terrain grid points, which, however, won't be !-- consistent with the input data. IF ( buildings_f%from_file .AND. buildings_f%lod == 1 ) THEN IF ( building_id_f%var(j,i) /= building_id_f%fill ) THEN DO k = nzb, nzt IF( zw(k) - ocean_offset == oro_max(nr) ) THEN IF ( buildings_f%var_2d(j,i) <= zu(k+1) - zw(k) ) THEN topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 2 ) ENDIF ENDIF ENDDO ENDIF ENDIF ! !-- Map 3D buildings onto terrain height. !-- In case of any slopes, map building on top of maximum terrain !-- height covered by the building. In other words, extend !-- building down to the respective local terrain-surface height. IF ( buildings_f%from_file .AND. buildings_f%lod == 2 ) THEN IF ( building_id_f%var(j,i) /= building_id_f%fill ) THEN ! !-- Extend building down to the terrain surface, i.e. fill-up !-- surface irregularities below a building. Note, oro_max !-- is already a discrete height according to the all-or-nothing !-- approach, i.e. grid box is either topography or atmosphere, !-- terrain top is defined at upper bound of the grid box. !-- Hence, check for zw in this case. !-- Note, do this only for buildings which are surface mounted, !-- i.e. building types 1-6. Below bridges, which are represented !-- exclusively by building type 7, terrain shape should be !-- maintained. IF ( building_type_f%from_file ) THEN IF ( building_type_f%var(j,i) /= 7 ) THEN DO k = topo_top_index + 1, nzt + 1 IF ( zu(k) - ocean_offset <= oro_max(nr) ) THEN topo_3d(k,j,i) = IBCLR( topo_3d(k,j,i), 0 ) topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 1 ) ENDIF ENDDO ! !-- After surface irregularities are smoothen, determine !-- lower start index where building starts. DO k = nzb, nzt IF ( zu(k) - ocean_offset <= oro_max(nr) ) & topo_top_index = k ENDDO ENDIF ENDIF ! !-- Finally, map building on top. k2 = 0 DO k = topo_top_index, nzt + 1 IF ( k2 <= buildings_f%nz-1 ) THEN IF ( buildings_f%var_3d(k2,j,i) == 1 ) THEN topo_3d(k,j,i) = IBCLR( topo_3d(k,j,i), 0 ) topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 2 ) ENDIF ENDIF k2 = k2 + 1 ENDDO ENDIF ENDIF ENDDO ENDDO ! !-- Horizontal exchange the oro_max array, which is required to for !-- initialization of building-surface properties. IF ( ALLOCATED( buildings_f%oro_max ) ) THEN CALL exchange_horiz_2d( buildings_f%oro_max(:,:) ) ENDIF ! !-- Deallocate temporary arrays required for processing and reading data IF ( ALLOCATED( oro_max ) ) DEALLOCATE( oro_max ) IF ( ALLOCATED( oro_max_l ) ) DEALLOCATE( oro_max_l ) IF ( ALLOCATED( build_ids_final ) ) DEALLOCATE( build_ids_final ) ! !-- Topography input via ASCII format. ELSE ocean_offset = MERGE( zw(0), 0.0_wp, ocean_mode ) ! !-- Initialize topography bit 0 (indicates obstacle) everywhere to zero !-- and clear all grid points at nzb, where alway a surface is defined. !-- Further, set also bit 1 (indicates terrain) at nzb, which is further !-- used for masked data output and further processing. Note, in the !-- ASCII case no distinction is made between buildings and terrain, !-- so that setting of bit 1 and 2 at the same time has no effect. topo_3d = IBSET( topo_3d, 0 ) topo_3d(nzb,:,:) = IBCLR( topo_3d(nzb,:,:), 0 ) topo_3d(nzb,:,:) = IBSET( topo_3d(nzb,:,:), 1 ) DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt ! !-- Flag topography for all grid points which are below !-- the local topography height. !-- Note, each topography is flagged as building (bit 2) as well as !-- terrain (bit 1) in order to employ urban-surface as well as !-- land-surface model. IF ( zu(k) - ocean_offset <= buildings_f%var_2d(j,i) ) THEN topo_3d(k,j,i) = IBCLR( topo_3d(k,j,i), 0 ) topo_3d(k,j,i) = IBCLR( topo_3d(k,j,i), 1 ) topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 2 ) ENDIF ENDDO ENDDO ENDDO ENDIF CALL exchange_horiz_int( topo_3d, nys, nyn, nxl, nxr, nzt, nbgp ) IF ( .NOT. bc_ns_cyc ) THEN IF ( nys == 0 ) topo_3d(:,-1,:) = topo_3d(:,0,:) IF ( nyn == ny ) topo_3d(:,ny+1,:) = topo_3d(:,ny,:) ENDIF IF ( .NOT. bc_lr_cyc ) THEN IF ( nxl == 0 ) topo_3d(:,:,-1) = topo_3d(:,:,0) IF ( nxr == nx ) topo_3d(:,:,nx+1) = topo_3d(:,:,nx) ENDIF END SUBROUTINE process_topography ! Description: ! -----------------------------------------------------------------------------! !> Filter topography, i.e. fill holes resolved by only one grid point. !> Such holes are suspected to lead to velocity blow-ups as continuity !> equation on discrete grid cannot be fulfilled in such case. !------------------------------------------------------------------------------! SUBROUTINE filter_topography( topo_3d ) USE control_parameters, & ONLY: bc_lr_cyc, bc_ns_cyc, message_string USE exchange_horiz_mod, & ONLY: exchange_horiz_int, exchange_horiz_2d_byte, exchange_horiz_2d_int USE indices, & ONLY: nbgp, nx, nxl, nxlg, nxr, nxrg, ny, nyn, nyng, nys, nysg, nzb, nzt USE netcdf_data_input_mod, & ONLY: building_id_f, building_type_f USE pegrid IMPLICIT NONE LOGICAL :: filled = .FALSE. !< flag indicating if holes were filled INTEGER(iwp) :: i !< running index along x-direction INTEGER(iwp) :: j !< running index along y-direction INTEGER(iwp) :: k !< running index along z-direction INTEGER(iwp) :: num_hole !< number of holes (in topography) resolved by only one grid point INTEGER(iwp) :: num_hole_l !< number of holes (in topography) resolved by only one grid point on local PE INTEGER(iwp) :: num_wall !< number of surrounding vertical walls for a single grid point INTEGER(iwp), DIMENSION(:,:,:), ALLOCATABLE :: topo_tmp !< temporary 3D-topography used to fill holes INTEGER(iwp), DIMENSION(nzb:nzt+1,nysg:nyng,nxlg:nxrg) :: topo_3d !< 3D-topography array merging buildings and orography ! !-- Before checking for holes, set lateral boundary conditions for !-- topography. After hole-filling, boundary conditions must be set again. !-- Several iterations are performed, in order to fill holes which might !-- emerge by the filling-algorithm itself. ALLOCATE( topo_tmp(nzb:nzt+1,nysg:nyng,nxlg:nxrg) ) topo_tmp = 0 num_hole = 99999 DO WHILE ( num_hole > 0 ) num_hole = 0 CALL exchange_horiz_int( topo_3d, nys, nyn, nxl, nxr, nzt, nbgp ) ! !-- Exchange also building ID and type. Note, building_type is an one-byte !-- variable. IF ( building_id_f%from_file ) & CALL exchange_horiz_2d_int( building_id_f%var, nys, nyn, nxl, nxr, nbgp ) IF ( building_type_f%from_file ) & CALL exchange_horiz_2d_byte( building_type_f%var, nys, nyn, nxl, nxr, nbgp ) topo_tmp = topo_3d ! !-- In case of non-cyclic lateral boundaries, assume lateral boundary to be !-- a solid wall. Thus, intermediate spaces of one grid point between !-- boundary and some topographic structure will be filled. IF ( .NOT. bc_ns_cyc ) THEN IF ( nys == 0 ) topo_tmp(:,-1,:) = IBCLR( topo_tmp(:,0,:), 0 ) IF ( nyn == ny ) topo_tmp(:,ny+1,:) = IBCLR( topo_tmp(:,ny,:), 0 ) ENDIF IF ( .NOT. bc_lr_cyc ) THEN IF ( nxl == 0 ) topo_tmp(:,:,-1) = IBCLR( topo_tmp(:,:,0), 0 ) IF ( nxr == nx ) topo_tmp(:,:,nx+1) = IBCLR( topo_tmp(:,:,nx), 0 ) ENDIF num_hole_l = 0 DO i = nxl, nxr DO j = nys, nyn DO k = nzb+1, nzt IF ( BTEST( topo_tmp(k,j,i), 0 ) ) THEN num_wall = 0 IF ( .NOT. BTEST( topo_tmp(k,j-1,i), 0 ) ) & num_wall = num_wall + 1 IF ( .NOT. BTEST( topo_tmp(k,j+1,i), 0 ) ) & num_wall = num_wall + 1 IF ( .NOT. BTEST( topo_tmp(k,j,i-1), 0 ) ) & num_wall = num_wall + 1 IF ( .NOT. BTEST( topo_tmp(k,j,i+1), 0 ) ) & num_wall = num_wall + 1 IF ( .NOT. BTEST( topo_tmp(k-1,j,i), 0 ) ) & num_wall = num_wall + 1 IF ( .NOT. BTEST( topo_tmp(k+1,j,i), 0 ) ) & num_wall = num_wall + 1 IF ( num_wall >= 4 ) THEN num_hole_l = num_hole_l + 1 ! !-- Clear flag 0 and set special flag ( bit 4) to indicate !-- that new topography point is a result of filtering process. topo_3d(k,j,i) = IBCLR( topo_3d(k,j,i), 0 ) topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 4 ) ! !-- If filled grid point is occupied by a building, classify !-- it as building grid point. IF ( building_type_f%from_file ) THEN IF ( building_type_f%var(j,i) /= & building_type_f%fill .OR. & building_type_f%var(j+1,i) /= & building_type_f%fill .OR. & building_type_f%var(j-1,i) /= & building_type_f%fill .OR. & building_type_f%var(j,i+1) /= & building_type_f%fill .OR. & building_type_f%var(j,i-1) /= & building_type_f%fill ) THEN ! !-- Set flag indicating building surfaces topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 2 ) ! !-- Set building_type and ID at this position if not !-- already set. This is required for proper !-- initialization of urban-surface energy balance !-- solver. IF ( building_type_f%var(j,i) == & building_type_f%fill ) THEN IF ( building_type_f%var(j+1,i) /= & building_type_f%fill ) THEN building_type_f%var(j,i) = & building_type_f%var(j+1,i) building_id_f%var(j,i) = & building_id_f%var(j+1,i) ELSEIF ( building_type_f%var(j-1,i) /= & building_type_f%fill ) THEN building_type_f%var(j,i) = & building_type_f%var(j-1,i) building_id_f%var(j,i) = & building_id_f%var(j-1,i) ELSEIF ( building_type_f%var(j,i+1) /= & building_type_f%fill ) THEN building_type_f%var(j,i) = & building_type_f%var(j,i+1) building_id_f%var(j,i) = & building_id_f%var(j,i+1) ELSEIF ( building_type_f%var(j,i-1) /= & building_type_f%fill ) THEN building_type_f%var(j,i) = & building_type_f%var(j,i-1) building_id_f%var(j,i) = & building_id_f%var(j,i-1) ENDIF ENDIF ENDIF ENDIF ! !-- If filled grid point is already classified as building !-- everything is fine, else classify this grid point as !-- natural type grid point. This case, values for the !-- surface type are already set. IF ( .NOT. BTEST( topo_3d(k,j,i), 2 ) ) THEN topo_3d(k,j,i) = IBSET( topo_3d(k,j,i), 1 ) ENDIF ENDIF ENDIF ENDDO ENDDO ENDDO ! !-- Count the total number of holes, required for informative message. #if defined( __parallel ) CALL MPI_ALLREDUCE( num_hole_l, num_hole, 1, MPI_INTEGER, MPI_SUM, & comm2d, ierr ) #else num_hole = num_hole_l #endif IF ( num_hole > 0 .AND. .NOT. filled ) filled = .TRUE. ENDDO ! !-- Create an informative message if any holes were filled. IF ( filled ) THEN WRITE( message_string, * ) 'Topography was filtered, i.e. holes ' // & 'resolved by only one grid point ' // & 'were filled during initialization.' CALL message( 'init_grid', 'PA0430', 0, 0, 0, 6, 0 ) ENDIF DEALLOCATE( topo_tmp ) ! !-- Finally, exchange topo_3d array again and if necessary set Neumann boundary !-- condition in case of non-cyclic lateral boundaries. CALL exchange_horiz_int( topo_3d, nys, nyn, nxl, nxr, nzt, nbgp ) IF ( .NOT. bc_ns_cyc ) THEN IF ( nys == 0 ) topo_3d(:,-1,:) = topo_3d(:,0,:) IF ( nyn == ny ) topo_3d(:,ny+1,:) = topo_3d(:,ny,:) ENDIF IF ( .NOT. bc_lr_cyc ) THEN IF ( nxl == 0 ) topo_3d(:,:,-1) = topo_3d(:,:,0) IF ( nxr == nx ) topo_3d(:,:,nx+1) = topo_3d(:,:,nx) ENDIF ! !-- Exchange building ID and type. Note, building_type is an one-byte variable. IF ( building_id_f%from_file ) & CALL exchange_horiz_2d_int( building_id_f%var, nys, nyn, nxl, nxr, nbgp ) IF ( building_type_f%from_file ) & CALL exchange_horiz_2d_byte( building_type_f%var, nys, nyn, nxl, nxr, nbgp ) END SUBROUTINE filter_topography ! Description: ! -----------------------------------------------------------------------------! !> Reads topography information from file or sets generic topography. Moreover, !> all topography-relevant topography arrays are initialized, and grid flags !> are set. !------------------------------------------------------------------------------! SUBROUTINE init_topo( topo ) USE arrays_3d, & ONLY: zw USE control_parameters, & ONLY: bc_lr_cyc, bc_ns_cyc, building_height, building_length_x, & building_length_y, building_wall_left, building_wall_south, & canyon_height, canyon_wall_left, canyon_wall_south, & canyon_width_x, canyon_width_y, dp_level_ind_b, dz, & message_string, topography, topography_grid_convention, & tunnel_height, tunnel_length, tunnel_width_x, tunnel_width_y, & tunnel_wall_depth USE exchange_horiz_mod, & ONLY: exchange_horiz_int USE grid_variables, & ONLY: dx, dy USE indices, & ONLY: nbgp, nx, nxl, nxlg, nxr, nxrg, ny, nyn, nyng, nys, nysg, nz, & nzb, nzt USE kinds USE netcdf_data_input_mod, & ONLY: buildings_f, terrain_height_f USE pegrid IMPLICIT NONE INTEGER(iwp) :: bh !< temporary vertical index of building height INTEGER(iwp) :: ngp_bx !< grid point number of building size along x INTEGER(iwp) :: ngp_by !< grid point number of building size along y INTEGER(iwp) :: index_left_bwall !< index for left building wall INTEGER(iwp) :: index_right_bwall !< index for right building wall INTEGER(iwp) :: index_north_bwall !< index for north building wall INTEGER(iwp) :: index_south_bwall !< index for south building wall INTEGER(iwp) :: ch !< temporary vertical index for canyon height INTEGER(iwp) :: ngp_cx !< grid point number of canyon size along x INTEGER(iwp) :: ngp_cy !< grid point number of canyon size along y INTEGER(iwp) :: index_left_cwall !< index for left canyon wall INTEGER(iwp) :: index_right_cwall !< index for right canyon wall INTEGER(iwp) :: index_north_cwall !< index for north canyon wall INTEGER(iwp) :: index_south_cwall !< index for south canyon wall INTEGER(iwp) :: i !< index variable along x INTEGER(iwp) :: j !< index variable along y INTEGER(iwp) :: k !< index variable along z INTEGER(iwp) :: hv_in !< heavyside function to model inner tunnel surface INTEGER(iwp) :: hv_out !< heavyside function to model outer tunnel surface INTEGER(iwp) :: txe_out !< end position of outer tunnel wall in x INTEGER(iwp) :: txs_out !< start position of outer tunnel wall in x INTEGER(iwp) :: tye_out !< end position of outer tunnel wall in y INTEGER(iwp) :: tys_out !< start position of outer tunnel wall in y INTEGER(iwp) :: txe_in !< end position of inner tunnel wall in x INTEGER(iwp) :: txs_in !< start position of inner tunnel wall in x INTEGER(iwp) :: tye_in !< end position of inner tunnel wall in y INTEGER(iwp) :: tys_in !< start position of inner tunnel wall in y INTEGER(iwp) :: td !< tunnel wall depth INTEGER(iwp) :: th !< height of outer tunnel wall INTEGER(iwp), DIMENSION(:,:), ALLOCATABLE :: nzb_local !< index for topography top at cell-center INTEGER(iwp), DIMENSION(nzb:nzt+1,nysg:nyng,nxlg:nxrg) :: topo !< input array for 3D topography and dummy array for setting "outer"-flags ! !-- Check for correct setting of the namelist parameter topography. If !-- topography information is read from file but topography = 'flat', !-- initialization does not work properly. IF ( ( buildings_f%from_file .OR. terrain_height_f%from_file ) .AND. & TRIM( topography ) /= 'read_from_file' ) THEN message_string = 'If topography information is provided (via ' // & 'Netcdf or ASCII input) topography = ' // & '"read_from_file" is required.' CALL message( 'init_grid', 'PA0437', 1, 2, 0, 6, 0 ) ENDIF ! !-- Set outer and inner index arrays for non-flat topography. !-- Here consistency checks concerning domain size and periodicity are !-- necessary. !-- Within this SELECT CASE structure only nzb_local is initialized !-- individually depending on the chosen topography type, all other index !-- arrays are initialized further below. SELECT CASE ( TRIM( topography ) ) CASE ( 'flat' ) ! !-- Initialilize 3D topography array, used later for initializing flags topo(nzb+1:nzt+1,:,:) = IBSET( topo(nzb+1:nzt+1,:,:), 0 ) CASE ( 'closed_channel' ) ! !-- Initialilize 3D topography array, used later for initializing flags topo(nzb+1:nzt,:,:) = IBSET( topo(nzb+1:nzt,:,:), 0 ) CASE ( 'single_building' ) ! !-- Single rectangular building, by default centered in the middle of the !-- total domain ngp_bx = NINT( building_length_x / dx ) ngp_by = NINT( building_length_y / dy ) bh = MINLOC( ABS( zw - building_height ), 1 ) - 1 IF ( ABS( zw(bh) - building_height ) == & ABS( zw(bh+1) - building_height ) ) bh = bh + 1 IF ( building_wall_left == 9999999.9_wp ) THEN building_wall_left = ( nx + 1 - ngp_bx ) / 2 * dx ENDIF index_left_bwall = NINT( building_wall_left / dx ) index_right_bwall = index_left_bwall + ngp_bx IF ( building_wall_south == 9999999.9_wp ) THEN building_wall_south = ( ny + 1 - ngp_by ) / 2 * dy ENDIF index_south_bwall = NINT( building_wall_south / dy ) index_north_bwall = index_south_bwall + ngp_by ! !-- Building size has to meet some requirements IF ( ( index_left_bwall < 1 ) .OR. ( index_right_bwall > nx-1 ) .OR. & ( index_right_bwall < index_left_bwall+3 ) .OR. & ( index_south_bwall < 1 ) .OR. ( index_north_bwall > ny-1 ) .OR.& ( index_north_bwall < index_south_bwall+3 ) ) THEN WRITE( message_string, * ) 'inconsistent building parameters:', & '&index_left_bwall=', index_left_bwall, & 'index_right_bwall=', index_right_bwall, & 'index_south_bwall=', index_south_bwall, & 'index_north_bwall=', index_north_bwall, & 'nx=', nx, 'ny=', ny CALL message( 'init_grid', 'PA0203', 1, 2, 0, 6, 0 ) ENDIF ALLOCATE( nzb_local(nysg:nyng,nxlg:nxrg) ) nzb_local = 0 ! !-- Define the building. IF ( index_left_bwall <= nxr .AND. index_right_bwall >= nxl .AND. & index_south_bwall <= nyn .AND. index_north_bwall >= nys ) & nzb_local(MAX(nys,index_south_bwall):MIN(nyn,index_north_bwall), & MAX(nxl,index_left_bwall):MIN(nxr,index_right_bwall)) = bh ! !-- Set bit array on basis of nzb_local DO i = nxl, nxr DO j = nys, nyn topo(nzb_local(j,i)+1:nzt+1,j,i) = & IBSET( topo(nzb_local(j,i)+1:nzt+1,j,i), 0 ) ENDDO ENDDO DEALLOCATE( nzb_local ) CALL exchange_horiz_int( topo, nys, nyn, nxl, nxr, nzt, nbgp ) ! !-- Set boundary conditions also for flags. Can be interpreted as Neumann !-- boundary conditions for topography. IF ( .NOT. bc_ns_cyc ) THEN IF ( nys == 0 ) THEN DO i = 1, nbgp topo(:,nys-i,:) = topo(:,nys,:) ENDDO ENDIF IF ( nyn == ny ) THEN DO i = 1, nbgp topo(:,nyn+i,:) = topo(:,nyn,:) ENDDO ENDIF ENDIF IF ( .NOT. bc_lr_cyc ) THEN IF ( nxl == 0 ) THEN DO i = 1, nbgp topo(:,:,nxl-i) = topo(:,:,nxl) ENDDO ENDIF IF ( nxr == nx ) THEN DO i = 1, nbgp topo(:,:,nxr+i) = topo(:,:,nxr) ENDDO ENDIF ENDIF CASE ( 'single_street_canyon' ) ! !-- Single quasi-2D street canyon of infinite length in x or y direction. !-- The canyon is centered in the other direction by default. IF ( canyon_width_x /= 9999999.9_wp ) THEN ! !-- Street canyon in y direction ngp_cx = NINT( canyon_width_x / dx ) IF ( canyon_wall_left == 9999999.9_wp ) THEN canyon_wall_left = ( nx + 1 - ngp_cx ) / 2 * dx ENDIF index_left_cwall= NINT( canyon_wall_left / dx ) index_right_cwall= index_left_cwall+ ngp_cx ELSEIF ( canyon_width_y /= 9999999.9_wp ) THEN ! !-- Street canyon in x direction ngp_cy = NINT( canyon_width_y / dy ) IF ( canyon_wall_south == 9999999.9_wp ) THEN canyon_wall_south = ( ny + 1 - ngp_cy ) / 2 * dy ENDIF index_south_cwall = NINT( canyon_wall_south / dy ) index_north_cwall = index_south_cwall + ngp_cy ELSE message_string = 'no street canyon width given' CALL message( 'init_grid', 'PA0204', 1, 2, 0, 6, 0 ) ENDIF ch = MINLOC( ABS( zw - canyon_height ), 1 ) - 1 IF ( ABS( zw(ch) - canyon_height ) == & ABS( zw(ch+1) - canyon_height ) ) ch = ch + 1 dp_level_ind_b = ch ! !-- Street canyon size has to meet some requirements IF ( canyon_width_x /= 9999999.9_wp ) THEN IF ( ( index_left_cwall< 1 ) .OR. ( index_right_cwall> nx-1 ) .OR.& ( ngp_cx < 3 ) ) THEN WRITE( message_string, * ) 'inconsistent canyon parameters:', & '&index_left_cwall=', index_left_cwall, & ' index_right_cwall=', index_right_cwall, & ' ngp_cx=', ngp_cx, & ' ch=', ch, ' nx=', nx, ' ny=', ny CALL message( 'init_grid', 'PA0205', 1, 2, 0, 6, 0 ) ENDIF ELSEIF ( canyon_width_y /= 9999999.9_wp ) THEN IF ( ( index_south_cwall < 1 ) .OR. & ( index_north_cwall > ny-1 ) .OR. ( ngp_cy < 3 ) ) THEN WRITE( message_string, * ) 'inconsistent canyon parameters:', & '&index_south_cwall=', index_south_cwall, & ' index_north_cwall=', index_north_cwall, & ' ngp_cy=', ngp_cy, & ' ch=', ch, ' nx=', nx, ' ny=', ny CALL message( 'init_grid', 'PA0206', 1, 2, 0, 6, 0 ) ENDIF ENDIF IF ( canyon_width_x /= 9999999.9_wp .AND. & canyon_width_y /= 9999999.9_wp ) THEN message_string = 'inconsistent canyon parameters:' // & '&street canyon can only be oriented' // & ' either in x- or in y-direction' CALL message( 'init_grid', 'PA0207', 1, 2, 0, 6, 0 ) ENDIF ALLOCATE( nzb_local(nysg:nyng,nxlg:nxrg) ) nzb_local = ch IF ( canyon_width_x /= 9999999.9_wp ) THEN IF ( index_left_cwall<= nxr .AND. index_right_cwall>= nxl ) & nzb_local(:,MAX(nxl,index_left_cwall+1):MIN(nxr,index_right_cwall-1)) = 0 ELSEIF ( canyon_width_y /= 9999999.9_wp ) THEN IF ( index_south_cwall <= nyn .AND. index_north_cwall >= nys ) & nzb_local(MAX(nys,index_south_cwall+1):MIN(nyn,index_north_cwall-1),:) = 0 ENDIF ! !-- Set bit array on basis of nzb_local DO i = nxl, nxr DO j = nys, nyn topo(nzb_local(j,i)+1:nzt+1,j,i) = & IBSET( topo(nzb_local(j,i)+1:nzt+1,j,i), 0 ) ENDDO ENDDO DEALLOCATE( nzb_local ) CALL exchange_horiz_int( topo, nys, nyn, nxl, nxr, nzt, nbgp ) ! !-- Set boundary conditions also for flags. Can be interpreted as Neumann !-- boundary conditions for topography. IF ( .NOT. bc_ns_cyc ) THEN IF ( nys == 0 ) THEN DO i = 1, nbgp topo(:,nys-i,:) = topo(:,nys,:) ENDDO ENDIF IF ( nyn == ny ) THEN DO i = 1, nbgp topo(:,nyn+i,:) = topo(:,nyn,:) ENDDO ENDIF ENDIF IF ( .NOT. bc_lr_cyc ) THEN IF ( nxl == 0 ) THEN DO i = 1, nbgp topo(:,:,nxl-i) = topo(:,:,nxl) ENDDO ENDIF IF ( nxr == nx ) THEN DO i = 1, nbgp topo(:,:,nxr+i) = topo(:,:,nxr) ENDDO ENDIF ENDIF CASE ( 'tunnel' ) ! !-- Tunnel height IF ( tunnel_height == 9999999.9_wp ) THEN th = zw( INT( 0.2 * nz) ) ELSE th = tunnel_height ENDIF ! !-- Tunnel-wall depth IF ( tunnel_wall_depth == 9999999.9_wp ) THEN td = MAX ( dx, dy, dz(1) ) ELSE td = tunnel_wall_depth ENDIF ! !-- Check for tunnel width IF ( tunnel_width_x == 9999999.9_wp .AND. & tunnel_width_y == 9999999.9_wp ) THEN message_string = 'No tunnel width is given. ' CALL message( 'init_grid', 'PA0280', 1, 2, 0, 6, 0 ) ENDIF IF ( tunnel_width_x /= 9999999.9_wp .AND. & tunnel_width_y /= 9999999.9_wp ) THEN message_string = 'Inconsistent tunnel parameters:' // & 'tunnel can only be oriented' // & 'either in x- or in y-direction.' CALL message( 'init_grid', 'PA0281', 1, 2, 0, 6, 0 ) ENDIF ! !-- Check for too small tunnel width in x- and y-direction IF ( tunnel_width_x /= 9999999.9_wp .AND. & tunnel_width_x - 2.0_wp * td <= 2.0_wp * dx ) THEN message_string = 'tunnel_width_x too small' CALL message( 'init_grid', 'PA0175', 1, 2, 0, 6, 0 ) ENDIF IF ( tunnel_width_y /= 9999999.9_wp .AND. & tunnel_width_y - 2.0_wp * td <= 2.0_wp * dy ) THEN message_string = 'tunnel_width_y too small' CALL message( 'init_grid', 'PA0455', 1, 2, 0, 6, 0 ) ENDIF ! !-- Check for too large tunnel width. !-- Tunnel axis along y. IF ( tunnel_width_x /= 9999999.9_wp ) THEN IF ( tunnel_width_x > ( nx + 1 ) * dx ) THEN message_string = 'tunnel_width_x too large' CALL message( 'init_grid', 'PA0282', 1, 2, 0, 6, 0 ) ENDIF txs_out = INT( ( nx + 1 ) * 0.5_wp * dx - tunnel_width_x * 0.5_wp ) txe_out = INT( ( nx + 1 ) * 0.5_wp * dx + tunnel_width_x * 0.5_wp ) txs_in = INT( ( nx + 1 ) * 0.5_wp * dx - & ( tunnel_width_x * 0.5_wp - td ) ) txe_in = INT( ( nx + 1 ) * 0.5_wp * dx + & ( tunnel_width_x * 0.5_wp - td ) ) tys_out = INT( ( ny + 1 ) * 0.5_wp * dy - tunnel_length * 0.5_wp ) tye_out = INT( ( ny + 1 ) * 0.5_wp * dy + tunnel_length * 0.5_wp ) tys_in = tys_out tye_in = tye_out ENDIF ! !-- Tunnel axis along x. IF ( tunnel_width_y /= 9999999.9_wp ) THEN IF ( tunnel_width_y > ( ny + 1 ) * dy ) THEN message_string = 'tunnel_width_y too large' CALL message( 'init_grid', 'PA0456', 1, 2, 0, 6, 0 ) ENDIF txs_out = INT( ( nx + 1 ) * 0.5_wp * dx - tunnel_length * 0.5_wp ) txe_out = INT( ( nx + 1 ) * 0.5_wp * dx + tunnel_length * 0.5_wp ) txs_in = txs_out txe_in = txe_out tys_out = INT( ( ny + 1 ) * 0.5_wp * dy - tunnel_width_y * 0.5_wp ) tye_out = INT( ( ny + 1 ) * 0.5_wp * dy + tunnel_width_y * 0.5_wp ) tys_in = INT( ( ny + 1 ) * 0.5_wp * dy - & ( tunnel_width_y * 0.5_wp - td ) ) tye_in = INT( ( ny + 1 ) * 0.5_wp * dy + & ( tunnel_width_y * 0.5_wp - td ) ) ENDIF topo = 0 DO i = nxl, nxr DO j = nys, nyn ! !-- Use heaviside function to model outer tunnel surface hv_out = th * 0.5_wp * & ( ( SIGN( 1.0_wp, i * dx - txs_out ) + 1.0_wp ) & - ( SIGN( 1.0_wp, i * dx - txe_out ) + 1.0_wp ) ) hv_out = hv_out * 0.5_wp * & ( ( SIGN( 1.0_wp, j * dy - tys_out ) + 1.0_wp ) & - ( SIGN( 1.0_wp, j * dy - tye_out ) + 1.0_wp ) ) ! !-- Use heaviside function to model inner tunnel surface hv_in = ( th - td ) * 0.5_wp * & ( ( SIGN( 1.0_wp, i * dx - txs_in ) + 1.0_wp ) & - ( SIGN( 1.0_wp, i * dx - txe_in ) + 1.0_wp ) ) hv_in = hv_in * 0.5_wp * & ( ( SIGN( 1.0_wp, j * dy - tys_in ) + 1.0_wp ) & - ( SIGN( 1.0_wp, j * dy - tye_in ) + 1.0_wp ) ) ! !-- Set flags at x-y-positions without any tunnel surface IF ( hv_out - hv_in == 0.0_wp ) THEN topo(nzb+1:nzt+1,j,i) = IBSET( topo(nzb+1:nzt+1,j,i), 0 ) ! !-- Set flags at x-y-positions with tunnel surfaces ELSE DO k = nzb + 1, nzt + 1 ! !-- Inner tunnel IF ( hv_out - hv_in == th ) THEN IF ( zw(k) <= hv_out ) THEN topo(k,j,i) = IBCLR( topo(k,j,i), 0 ) ELSE topo(k,j,i) = IBSET( topo(k,j,i), 0 ) ENDIF ENDIF ! !-- Lateral tunnel walls IF ( hv_out - hv_in == td ) THEN IF ( zw(k) <= hv_in ) THEN topo(k,j,i) = IBSET( topo(k,j,i), 0 ) ELSEIF ( zw(k) > hv_in .AND. zw(k) <= hv_out ) THEN topo(k,j,i) = IBCLR( topo(k,j,i), 0 ) ELSEIF ( zw(k) > hv_out ) THEN topo(k,j,i) = IBSET( topo(k,j,i), 0 ) ENDIF ENDIF ENDDO ENDIF ENDDO ENDDO CALL exchange_horiz_int( topo, nys, nyn, nxl, nxr, nzt, nbgp ) ! !-- Set boundary conditions also for flags. Can be interpreted as Neumann !-- boundary conditions for topography. IF ( .NOT. bc_ns_cyc ) THEN IF ( nys == 0 ) THEN DO i = 1, nbgp topo(:,nys-i,:) = topo(:,nys,:) ENDDO ENDIF IF ( nyn == ny ) THEN DO i = 1, nbgp topo(:,nyn+i,:) = topo(:,nyn,:) ENDDO ENDIF ENDIF IF ( .NOT. bc_lr_cyc ) THEN IF ( nxl == 0 ) THEN DO i = 1, nbgp topo(:,:,nxl-i) = topo(:,:,nxl) ENDDO ENDIF IF ( nxr == nx ) THEN DO i = 1, nbgp topo(:,:,nxr+i) = topo(:,:,nxr) ENDDO ENDIF ENDIF CASE ( 'read_from_file' ) ! !-- Note, topography information have been already read. !-- If required, further process topography, i.e. reference buildings on !-- top of orography and set temporary 3D topography array, which is !-- used later to set grid flags. Calling of this rouinte is also !-- required in case of ASCII input, even though no distinction between !-- terrain- and building height is made in this case. CALL process_topography( topo ) ! !-- Filter holes resolved by only one grid-point CALL filter_topography( topo ) ! !-- Exchange ghost-points, as well as add cyclic or Neumann boundary !-- conditions. CALL exchange_horiz_int( topo, nys, nyn, nxl, nxr, nzt, nbgp ) ! !-- Set lateral boundary conditions for topography on all ghost layers IF ( .NOT. bc_ns_cyc ) THEN IF ( nys == 0 ) THEN DO i = 1, nbgp topo(:,nys-i,:) = topo(:,nys,:) ENDDO ENDIF IF ( nyn == ny ) THEN DO i = 1, nbgp topo(:,nyn+i,:) = topo(:,nyn,:) ENDDO ENDIF ENDIF IF ( .NOT. bc_lr_cyc ) THEN IF ( nxl == 0 ) THEN DO i = 1, nbgp topo(:,:,nxl-i) = topo(:,:,nxl) ENDDO ENDIF IF ( nxr == nx ) THEN DO i = 1, nbgp topo(:,:,nxr+i) = topo(:,:,nxr) ENDDO ENDIF ENDIF CASE DEFAULT ! !-- The DEFAULT case is reached either if the parameter topography !-- contains a wrong character string or if the user has defined a special !-- case in the user interface. There, the subroutine user_init_grid !-- checks which of these two conditions applies. CALL user_init_grid( topo ) CALL filter_topography( topo ) END SELECT ! !-- Consistency checks and index array initialization are only required for !-- non-flat topography. IF ( TRIM( topography ) /= 'flat' ) THEN ! !-- In case of non-flat topography, check whether the convention how to !-- define the topography grid has been set correctly, or whether the default !-- is applicable. If this is not possible, abort. IF ( TRIM( topography_grid_convention ) == ' ' ) THEN IF ( TRIM( topography ) /= 'closed_channel' .AND. & TRIM( topography ) /= 'single_building' .AND. & TRIM( topography ) /= 'single_street_canyon' .AND. & TRIM( topography ) /= 'tunnel' .AND. & TRIM( topography ) /= 'read_from_file') THEN !-- The default value is not applicable here, because it is only valid !-- for the four standard cases 'single_building', !-- 'single_street_canyon', 'tunnel' and 'read_from_file' !-- defined in init_grid. WRITE( message_string, * ) & 'The value for "topography_grid_convention" ', & 'is not set. Its default value is & only valid for ', & '"topography" = ''single_building'', ''tunnel'' ', & '''single_street_canyon'', ''closed_channel'' & or ', & '''read_from_file''.', & '& Choose ''cell_edge'' or ''cell_center''.' CALL message( 'init_grid', 'PA0239', 1, 2, 0, 6, 0 ) ELSE !-- The default value is applicable here. !-- Set convention according to topography. IF ( TRIM( topography ) == 'single_building' .OR. & TRIM( topography ) == 'single_street_canyon' ) THEN topography_grid_convention = 'cell_edge' ELSEIF ( TRIM( topography ) == 'read_from_file' .OR. & TRIM( topography ) == 'tunnel') THEN topography_grid_convention = 'cell_center' ENDIF ENDIF ELSEIF ( TRIM( topography_grid_convention ) /= 'cell_edge' .AND. & TRIM( topography_grid_convention ) /= 'cell_center' ) THEN WRITE( message_string, * ) & 'The value for "topography_grid_convention" is ', & 'not recognized.& Choose ''cell_edge'' or ''cell_center''.' CALL message( 'init_grid', 'PA0240', 1, 2, 0, 6, 0 ) ENDIF IF ( topography_grid_convention == 'cell_edge' ) THEN ! !-- The array nzb_local as defined using the 'cell_edge' convention !-- describes the actual total size of topography which is defined at the !-- cell edges where u=0 on the topography walls in x-direction and v=0 !-- on the topography walls in y-direction. However, PALM uses individual !-- arrays nzb_u|v|w|s_inner|outer that are based on nzb_s_inner. !-- Therefore, the extent of topography in nzb_local is now reduced by !-- 1dx at the E topography walls and by 1dy at the N topography walls !-- to form the basis for nzb_s_inner. !-- Note, the reverse memory access (i-j instead of j-i) is absolutely !-- required at this point. DO j = nys+1, nyn+1 DO i = nxl-1, nxr DO k = nzb, nzt+1 IF ( BTEST( topo(k,j,i), 0 ) .OR. & BTEST( topo(k,j,i+1), 0 ) ) & topo(k,j,i) = IBSET( topo(k,j,i), 0 ) ENDDO ENDDO ENDDO CALL exchange_horiz_int( topo, nys, nyn, nxl, nxr, nzt, nbgp ) DO i = nxl, nxr+1 DO j = nys-1, nyn DO k = nzb, nzt+1 IF ( BTEST( topo(k,j,i), 0 ) .OR. & BTEST( topo(k,j+1,i), 0 ) ) & topo(k,j,i) = IBSET( topo(k,j,i), 0 ) ENDDO ENDDO ENDDO CALL exchange_horiz_int( topo, nys, nyn, nxl, nxr, nzt, nbgp ) ENDIF ENDIF END SUBROUTINE init_topo SUBROUTINE set_topo_flags(topo) USE control_parameters, & ONLY: bc_lr_cyc, bc_ns_cyc, constant_flux_layer, & scalar_advec, topography, use_surface_fluxes, use_top_fluxes USE exchange_horiz_mod, & ONLY: exchange_horiz_int USE indices, & ONLY: nbgp, nx, nxl, nxlg, nxr, nxrg, ny, nyn, nyng, nys, nysg, nzb, & nzt, topo_top_ind, wall_flags_static_0, wall_flags_total_0 USE kinds IMPLICIT NONE INTEGER(iwp) :: i !< index variable along x INTEGER(iwp) :: ibit !< integer bit position of topgraphy masking array INTEGER(iwp) :: j !< index variable along y INTEGER(iwp) :: k !< index variable along z INTEGER(iwp), DIMENSION(nzb:nzt+1,nysg:nyng,nxlg:nxrg) :: topo !< input array for 3D topography and dummy array for setting "outer"-flags ALLOCATE( wall_flags_static_0(nzb:nzt+1,nysg:nyng,nxlg:nxrg) ) wall_flags_static_0 = 0 ! !-- Set-up topography flags. First, set flags only for s, u, v and w-grid. !-- Further special flags will be set in following loops. DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt+1 ! !-- scalar grid IF ( BTEST( topo(k,j,i), 0 ) ) & wall_flags_static_0(k,j,i) = IBSET( wall_flags_static_0(k,j,i), 0 ) ! !-- u grid IF ( BTEST( topo(k,j,i), 0 ) .AND. & BTEST( topo(k,j,i-1), 0 ) ) & wall_flags_static_0(k,j,i) = IBSET( wall_flags_static_0(k,j,i), 1 ) ! !-- v grid IF ( BTEST( topo(k,j,i), 0 ) .AND. & BTEST( topo(k,j-1,i), 0 ) ) & wall_flags_static_0(k,j,i) = IBSET( wall_flags_static_0(k,j,i), 2 ) ENDDO DO k = nzb, nzt ! !-- w grid IF ( BTEST( topo(k,j,i), 0 ) .AND. & BTEST( topo(k+1,j,i), 0 ) ) & wall_flags_static_0(k,j,i) = IBSET( wall_flags_static_0(k,j,i), 3 ) ENDDO IF ( topography /= 'closed_channel' ) THEN wall_flags_static_0(nzt+1,j,i) = IBSET( wall_flags_static_0(nzt+1,j,i), 3 ) ENDIF ENDDO ENDDO CALL exchange_horiz_int( wall_flags_static_0, nys, nyn, nxl, nxr, nzt, nbgp ) ! !-- Set outer array for scalars to mask near-surface grid points. Note, on !-- basis of flag 24 futher flags will be derived which are used to control !-- production of subgrid TKE production near walls. ALLOCATE( wall_flags_total_0(nzb:nzt+1,nysg:nyng,nxlg:nxrg) ) wall_flags_total_0 = 0 DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt+1 wall_flags_total_0(k,j,i) = IOR( wall_flags_total_0(k,j,i), wall_flags_static_0(k,j,i) ) ENDDO ENDDO ENDDO CALL exchange_horiz_int( wall_flags_total_0, nys, nyn, nxl, nxr, nzt, nbgp ) DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt+1 IF ( BTEST( wall_flags_total_0(k,j-1,i), 0 ) .AND. & BTEST( wall_flags_total_0(k,j+1,i), 0 ) .AND. & BTEST( wall_flags_total_0(k,j,i-1), 0 ) .AND. & BTEST( wall_flags_total_0(k,j,i+1), 0 ) .AND. & BTEST( wall_flags_total_0(k,j-1,i-1), 0 ) .AND. & BTEST( wall_flags_total_0(k,j+1,i-1), 0 ) .AND. & BTEST( wall_flags_total_0(k,j-1,i+1), 0 ) .AND. & BTEST( wall_flags_total_0(k,j+1,i+1), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 24 ) ENDDO ENDDO ENDDO ! !-- Set further special flags DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt+1 ! !-- scalar grid, former nzb_diff_s_inner. !-- Note, use this flag also to mask topography in diffusion_u and !-- diffusion_v along the vertical direction. In case of !-- use_surface_fluxes, fluxes are calculated via MOST, else, simple !-- gradient approach is applied. Please note, in case of u- and v- !-- diffuison, a small error is made at edges (on the east side for u, !-- at the north side for v), since topography on scalar grid point !-- is used instead of topography on u/v-grid. As number of topography grid !-- points on uv-grid is different than s-grid, different number of !-- surface elements would be required. In order to avoid this, !-- treat edges (u(k,j,i+1)) simply by a gradient approach, i.e. these !-- points are not masked within diffusion_u. Tests had shown that the !-- effect on the flow is negligible. IF ( constant_flux_layer .OR. use_surface_fluxes ) THEN IF ( BTEST( wall_flags_total_0(k,j,i), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 8 ) ELSE wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 8 ) ENDIF ENDDO ! !-- Special flag to control vertical diffusion at model top - former !-- nzt_diff wall_flags_total_0(:,j,i) = IBSET( wall_flags_total_0(:,j,i), 9 ) IF ( use_top_fluxes ) & wall_flags_total_0(nzt+1,j,i) = IBCLR( wall_flags_total_0(nzt+1,j,i), 9 ) DO k = nzb+1, nzt ! !-- Special flag on u grid, former nzb_u_inner + 1, required !-- for disturb_field and initialization. Do not disturb directly at !-- topography, as well as initialize u with zero one grid point outside !-- of topography. IF ( BTEST( wall_flags_total_0(k-1,j,i), 1 ) .AND. & BTEST( wall_flags_total_0(k,j,i), 1 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 1 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 20 ) ! !-- Special flag on v grid, former nzb_v_inner + 1, required !-- for disturb_field and initialization. Do not disturb directly at !-- topography, as well as initialize v with zero one grid point outside !-- of topography. IF ( BTEST( wall_flags_total_0(k-1,j,i), 2 ) .AND. & BTEST( wall_flags_total_0(k,j,i), 2 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 2 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 21 ) ! !-- Special flag on scalar grid, former nzb_s_inner+1. Used for !-- lpm_sgs_tke IF ( BTEST( wall_flags_total_0(k,j,i), 0 ) .AND. & BTEST( wall_flags_total_0(k-1,j,i), 0 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 25 ) ! !-- Special flag on scalar grid, nzb_diff_s_outer - 1, required in !-- in production_e IF ( constant_flux_layer .OR. use_surface_fluxes ) THEN IF ( BTEST( wall_flags_total_0(k,j,i), 24 ) .AND. & BTEST( wall_flags_total_0(k-1,j,i), 24 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 29 ) ELSE IF ( BTEST( wall_flags_total_0(k,j,i), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 29 ) ENDIF ! !-- Special flag on scalar grid, nzb_diff_s_outer - 1, required in !-- in production_e IF ( constant_flux_layer .OR. use_surface_fluxes ) THEN IF ( BTEST( wall_flags_total_0(k,j,i), 0 ) .AND. & BTEST( wall_flags_total_0(k-1,j,i), 0 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 30 ) ELSE IF ( BTEST( wall_flags_total_0(k,j,i), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 30 ) ENDIF ENDDO ! !-- Flags indicating downward facing walls DO k = nzb+1, nzt+1 ! !-- Scalar grid IF ( BTEST( wall_flags_total_0(k-1,j,i), 0 ) .AND. & .NOT. BTEST( wall_flags_total_0(k,j,i), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 13 ) ! !-- Downward facing wall on u grid IF ( BTEST( wall_flags_total_0(k-1,j,i), 1 ) .AND. & .NOT. BTEST( wall_flags_total_0(k,j,i), 1 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 15 ) ! !-- Downward facing wall on v grid IF ( BTEST( wall_flags_total_0(k-1,j,i), 2 ) .AND. & .NOT. BTEST( wall_flags_total_0(k,j,i), 2 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 17 ) ! !-- Downward facing wall on w grid IF ( BTEST( wall_flags_total_0(k-1,j,i), 3 ) .AND. & .NOT. BTEST( wall_flags_total_0(k,j,i), 3 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 19 ) ENDDO ! !-- Flags indicating upward facing walls DO k = nzb, nzt ! !-- Upward facing wall on scalar grid IF ( .NOT. BTEST( wall_flags_total_0(k,j,i), 0 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 12 ) ! !-- Upward facing wall on u grid IF ( .NOT. BTEST( wall_flags_total_0(k,j,i), 1 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 1 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 14 ) ! !-- Upward facing wall on v grid IF ( .NOT. BTEST( wall_flags_total_0(k,j,i), 2 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 2 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 16 ) ! !-- Upward facing wall on w grid IF ( .NOT. BTEST( wall_flags_total_0(k,j,i), 3 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 3 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 18 ) ! !-- Special flag on scalar grid, former nzb_s_inner IF ( BTEST( wall_flags_total_0(k,j,i), 0 ) .OR. & BTEST( wall_flags_total_0(k,j,i), 12 ) .OR. & BTEST( wall_flags_total_0(k,j,i), 13 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 22 ) ! !-- Special flag on scalar grid, nzb_diff_s_inner - 1, required for !-- flow_statistics IF ( constant_flux_layer .OR. use_surface_fluxes ) THEN IF ( BTEST( wall_flags_total_0(k,j,i), 0 ) .AND. & BTEST( wall_flags_total_0(k+1,j,i), 0 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 23 ) ELSE IF ( BTEST( wall_flags_total_0(k,j,i), 22 ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 23 ) ENDIF ENDDO wall_flags_total_0(nzt+1,j,i) = IBSET( wall_flags_total_0(nzt+1,j,i), 22 ) wall_flags_total_0(nzt+1,j,i) = IBSET( wall_flags_total_0(nzt+1,j,i), 23 ) ! !-- Set flags indicating that topography is close by in horizontal !-- direction, i.e. flags that infold the topography. These will be used !-- to set advection flags for passive scalars, where due to large !-- gradients near buildings stationary numerical oscillations can produce !-- unrealistically high concentrations. This is only necessary if !-- WS-scheme is applied for scalar advection. Note, these flags will be !-- only used for passive scalars such as chemical species or aerosols. IF ( scalar_advec == 'ws-scheme' ) THEN DO k = nzb, nzt IF ( BTEST( wall_flags_total_0(k,j,i), 0 ) .AND. ( & ANY( .NOT. BTEST( wall_flags_total_0(k,j-3:j+3,i-1), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j-3:j+3,i-2), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j-3:j+3,i-3), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j-3:j+3,i+1), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j-3:j+3,i+2), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j-3:j+3,i+3), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j-1,i-3:i+3), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j-2,i-3:i+3), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j-3,i-3:i+3), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j+1,i-3:i+3), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j+2,i-3:i+3), 0 ) ) .OR.& ANY( .NOT. BTEST( wall_flags_total_0(k,j+3,i-3:i+3), 0 ) ) & ) ) & wall_flags_total_0(k,j,i) = IBSET( wall_flags_total_0(k,j,i), 31 ) ENDDO ENDIF ENDDO ENDDO ! !-- Finally, set identification flags indicating natural terrain or buildings. !-- Natural terrain grid points. Information on the type of the surface is !-- stored in bit 1 of 3D Integer array topo. However, this bit is only set !-- when topography is read from file. In order to run the land-surface model !-- also without topography information, set bit 1 explicitely in this case. !-- !-- Natural terrain grid points !-- If no topography is initialized, the land-surface is at k = nzb. IF ( TRIM( topography ) /= 'read_from_file' ) THEN wall_flags_static_0(nzb,:,:) = IBSET( wall_flags_static_0(nzb,:,:), 5 ) ELSE DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt+1 ! !-- Natural terrain grid point IF ( BTEST( topo(k,j,i), 1 ) ) & wall_flags_static_0(k,j,i) = IBSET( wall_flags_static_0(k,j,i), 5 ) ENDDO ENDDO ENDDO ENDIF ! !-- Building grid points. DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt+1 IF ( BTEST( topo(k,j,i), 2 ) ) & wall_flags_static_0(k,j,i) = IBSET( wall_flags_static_0(k,j,i), 6 ) ENDDO ENDDO ENDDO ! !-- Set flag 4, indicating new topography grid points due to filtering. DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt+1 IF ( BTEST( topo(k,j,i), 4 ) ) & wall_flags_static_0(k,j,i) = IBSET( wall_flags_static_0(k,j,i), 4 ) ENDDO ENDDO ENDDO CALL exchange_horiz_int( wall_flags_static_0, nys, nyn, nxl, nxr, nzt, nbgp ) DO i = nxl, nxr DO j = nys, nyn DO k = nzb, nzt+1 wall_flags_total_0(k,j,i) = IOR( wall_flags_total_0(k,j,i), wall_flags_static_0(k,j,i) ) ENDDO ENDDO ENDDO ! !-- Exchange ghost points for wall flags CALL exchange_horiz_int( wall_flags_total_0, nys, nyn, nxl, nxr, nzt, nbgp ) ! !-- Set boundary conditions also for flags. Can be interpreted as Neumann !-- boundary conditions for topography. IF ( .NOT. bc_ns_cyc ) THEN IF ( nys == 0 ) THEN DO i = 1, nbgp wall_flags_total_0(:,nys-i,:) = wall_flags_total_0(:,nys,:) ENDDO ENDIF IF ( nyn == ny ) THEN DO i = 1, nbgp wall_flags_total_0(:,nyn+i,:) = wall_flags_total_0(:,nyn,:) ENDDO ENDIF ENDIF IF ( .NOT. bc_lr_cyc ) THEN IF ( nxl == 0 ) THEN DO i = 1, nbgp wall_flags_total_0(:,:,nxl-i) = wall_flags_total_0(:,:,nxl) ENDDO ENDIF IF ( nxr == nx ) THEN DO i = 1, nbgp wall_flags_total_0(:,:,nxr+i) = wall_flags_total_0(:,:,nxr) ENDDO ENDIF ENDIF ! !-- Pre-calculate topography top indices (former get_topography_top_index !-- function) ALLOCATE( topo_top_ind(nysg:nyng,nxlg:nxrg,0:4) ) ! !-- Uppermost topography index on scalar grid ibit = 12 topo_top_ind(:,:,0) = MAXLOC( & MERGE( 1, 0, & BTEST( wall_flags_total_0(:,:,:), ibit ) & ), DIM = 1 & ) - 1 ! !-- Uppermost topography index on u grid ibit = 14 topo_top_ind(:,:,1) = MAXLOC( & MERGE( 1, 0, & BTEST( wall_flags_total_0(:,:,:), ibit ) & ), DIM = 1 & ) - 1 ! !-- Uppermost topography index on v grid ibit = 16 topo_top_ind(:,:,2) = MAXLOC( & MERGE( 1, 0, & BTEST( wall_flags_total_0(:,:,:), ibit ) & ), DIM = 1 & ) - 1 ! !-- Uppermost topography index on w grid ibit = 18 topo_top_ind(:,:,3) = MAXLOC( & MERGE( 1, 0, & BTEST( wall_flags_total_0(:,:,:), ibit ) & ), DIM = 1 & ) - 1 ! !-- Uppermost topography index on scalar outer grid ibit = 24 topo_top_ind(:,:,4) = MAXLOC( & MERGE( 1, 0, & BTEST( wall_flags_total_0(:,:,:), ibit ) & ), DIM = 1 & ) - 1 END SUBROUTINE set_topo_flags